Barco HDF W series Скачать руководство пользователя страница 288

Страница: 288 / 319

17. Servicing

Take off the dummy cover plate.

Insert the new input module in its compartment.

Make sure the module seats in its sliders (2).
Pull in the module until the contacts (3) are fully inserted into the connectors.

Fixate both

xation screws.

Image 17-2
Fixate input

17.2 Replacement of the dust

lter on the front side

Necessary parts

New HEPA dust

lter for the front side (R9854470).

How to replace the HEPA dust

lter on the front side

Remove the front cover of the projector, see "Removal of the front cover", page 275.

Remove the HEPA dust

lter on the front side by pulling the two spring clamps away from the

lter and then moving the

lter forwards.

Image 17-3
Front

lter

Insert a new HEPA

lter by pulling the two spring clamps away and move the

lter into position.

Caution:

Make sure that the air

ow indicated on the dust

lter match with the air

ow of the fans.

Reinstall the front cover of the projector, see "Installation of the front cover", page 278.

AUTION

Never install a used HEPA

lter. Always install a new HEPA

lter.

6. High Efficiency Particulate Arrestant

284

R5905158 HDF SERIES 16/06/2015

Содержание HDF W series
































































































































































































































































































































Результаты поиска

Содержание HDF W series

Отзывы:

Бренды по названию

Популярные бренды

Barco HDF W series, Инструкция по использованию и установке

Результаты поиска

Содержание HDF W series

Отзывы:

Бренды по названию

Популярные бренды