background image

 

 

 

1. INTRODUCTION 

 

The BARCO Medical Grade MDSC8156 series are color high resolution liquid crystal displays especially 
designed for medical imaging applications. 
 
The MDSC8156 is a 

56” Color Flat Panel Display, intended to replace typical multi-monitor arrays in 

medical applications, whenever a large screen is needed in addition to high resolution, while offering 
the same good rendering in greyscale medical imaging thanks to the DICOM conformance. 
It has been designed to meet the specific need of typical monitor set-up in examination rooms, 
where monochrome and color pictures have to be displayed and freely positioned over the screen, 
when processed by a suitable graphic engine. 
 
The MDSC8156 shall provide 8 Mpixel screen resolution, high luminance and accept digital inputs, 
according to the DVI standard, with the native panel resolution of 3840 x 2160. 
The MDSC8156 can operate in two modes, Single Link and Dual Link, configurable via a menu setting. 
 
Other important features like the very large viewing angle, the high brightness level, the backlight 
stabilization, the greyscale correction and the compliance with the DICOM standards, will help the 
users avoiding misinterpretation in medical diagnosis. 
 
The MDSC8156 is also suitable for viewing a large range of contents, as color temperature and 
color gamma adjustments are provided. 
The display can also be controlled by remote, through a serial or Ethernet communication link. 
 
The MDSC8156 shall be supplied with VESA 400 mounting interfaces. 
 
This monitor follows the provisions of Medical Directive: 
93/42/EEC, Amended by 2007/47/EC (Medical device Class I) 
 
The product has been designed to meet the following medical safety requirements, including; 
UL60601-1 1st Ed, 2006-04-26; CAN/CSA-C22.2 No. 601.1-M90, 2005; 
EN 60601-1:1990 + A1:1993 + A2:1995; IEC 60601-1:1988 + A1:1991 + A2:1995 2nd Ed. 
ANSI/AAMI ES 60601-1: 2005, CAN /CSA 

–C22.2 No. 60601-1: 2008; IEC 60601-1:2005 3

rd

 Ed. 

 

 

The product is intended for indoor use 

 

Class I Equipment, according to the type of protection against electric shock  (*) 

 

Detachable supply connection  

 

Stationary, in case of “slave” monitor placed in Control Room, not fixed on wall; 

 

Fixed, when mounted in MCS. 

 

Continuous Operation, according to the mode of operation, 

 

Degree of protection against ingress of water: IP21 (only for model provided with protective screen)  

 

Do not use in areas with flammable anesthetics 

 

Do not use in oxygen rich environments

(**) 

 

 

The monitor is not intended to be sterilized 

 

The monitor has been designed to be used in landscape position with 0 degree of tilt (no tilted 
forward or backward) 
 

  (*) To avoid the risk of electric shock, this equipment must only be connected to a supply mains with 
         protective earth 

 

(**) This equipment does not have a gas-sealed electronics enclosure and could ignite any flammable or 

explosive gases present in its environment. 

 
 
 
 
 
 
 
 
 
 

Содержание FIMI MDSC8156













































Отзывы: