![background image](http://html1.mh-extra.com/html/barco/f80-series/f80-series_user-manual_3876313037.webp)
R5906852-01
F80 series
37
4.3.2 Power on projector
If not already connected, connect the female side of the power cord with the power input socket of
the projector. For more details see section dedicated to the power cord installation.
The background image of the startup screen and info screens can be changed with Projector
Toolset with an installed F80 plug-in.
Description
Plug the 3-prong plug of power cord into a grounded AC outlet. The projector will go to
READY
mode. During
this stage the system boots and performs the internal check of the boards. The Power
On/Off button
will
BLINKING WHITE until
READY
mode is achieved. Once in
READY
mode, the
Power On/Off
button will be lit
WHITE.
4.3.3 Going from READY to ON
Description
Press the
Power On/Off
button on the projector, or the
Power On
button on the remote control. The projector
will power
ON
. The
Power On/Off
button will BLINK BLUE during the transition from
READY
to
ON
. Once the
projector is on, the
Power On/Off
button will be lit BLUE.
4.3.4 Going from ON to READY
Description
Press and hold the
Power on/off
button on the projector for 3 seconds, or press the
Power Off
button on the
remote control. The projector will power down through a cool down phase. The
Power on/off
button will BLINK
WHITE during the transition from
ON
to
READY
. Once the projector is in
READY
, the
Power on/off
button will
be lit WHITE.
4.3.5 Going from READY to ECO standby
Description
If ECO Standby mode is enabled in the service menu (refer to the section "GUI - system settings/Standby
ECO", in User Guide) the projector will automatically go to
ECO
standby mode after a time-out (default 15
minutes). All electronics (including fans, pumps,...) go down except for a very small wake up controller. The
Power on/off
button will FLASH WHITE every second.
4.3.6 Going from ECO to ON
Description
Press the
Power on/off
button on the projector or the
Power On
button on the remote control. The projector
goes from
ECO
directly to
ON
. The projector will go through the same booting phase as on power plugging,
then do the transition from
READY
to
ON
. Of course startup-time will be longer then from
READY
to
ON
.
4.3.7 Wake on LAN (WOL)
Description
Wake-on-LAN (WOL), the standard ethernet network command, can be used to awakened or to turn on the
projector by network message.
Used alone, the WOL command allows to switch in READY mode. A JSON command must be performed in
addition to make the projector turn in to ON mode:
1.
Send WOL.
2.
Wait for connection to façade/prospector (the unit does provide feedback when it
’
s ready).
3.
Wait for ready state.
Содержание F80 series
