![background image](http://html1.mh-extra.com/html/barco/dp2k-e-series/dp2k-e-series_user-and-installation-manual_4092713020.webp)
3. Getting started
3.1
Installation requirements
Environment conditions
Table below summarizes the physical environment in which the DP2K-E series projector may be safely operated or stored.
Environment
Operating
Non-Operating
Ambient Temperature
10°C (50°F) to 35°C (95°F)
-20°C (-4°F) to 60°C (140°F)
Air cleanliness
Clean of
fi
ce environment (equivalent with cleanroom
standard ISO 14644-1 ISO Class 9)
n.a.
Humidity
0% to 85% RH Non-condensed
0% to 93% RH Non-Condensed
Altitude
-60 (-197Ft) to 2000m (9843Ft)
-60 (-197Ft) to 10000m (32810Ft)
Let the projector acclimatize after unpacking. Neglecting this may result in a startup failure of the Light Pro-
cessor Unit.
Cooling requirements
The projector is fan cooled and must be installed with suf
fi
cient space around the projector head, minimum 20 cm (8 inch) to ensure
suf
fi
cient air
fl
ow. It should be used in an area where the ambient temperature, as measured at the projector air inlet, does not
exceed 35°C (95°F).
Main Power requirements
The DP2K-E series projector operates from a nominal mono phase power net with a separate earth ground PE.
Projector
Power requirements
DP2K-6E
200-240 VAC, 50-60Hz, 6,25A at 200 VAC
The power cord required to connect the projector with the power net is not delivered with the projector. It is the responsibility of the
customer to provide the correct type of power cord. The cross-sectional area of the conductors in the power supply cord shall not
be less than
1mm
2
(18AWG)
, minimum 300V.
To protect operating personnel, the National Electrical Manufacturers Association (NEMA) recommends that the instrument panel
and cabinet be grounded. In no event shall this projector be operated without an adequate cabinet ground connection.
The AC supply must be installed by a quali
fi
ed electrician in conformance to local codes. Hardware, wire sizes and conduit types
must comply with local codes.
A readily accessible disconnect device shall be incorporated externally to the equipment for removal of the power.
UPS requirements
The Uninterruptible Power Supply (UPS), also known as a Continuous Power Supply (CPS), must have an output voltage of 200-
240V at 50-60Hz and must be capable of delivering an output power of 250W. This UPS provides only power for the electronics and
lamp cooling, but not for the lamp.
The connection between the UPS unit and the UPS inlet of the projector must be done with a certi
fi
ed AC power supply cord of
minimum 0,75 mm² or 18 AWG and minimum 300V.
W
ARNING
:
Disconnect the power cord for removal of all power from the unit.
The DP2K-E series projector does not have a built in UPS unit.
Projector weight
Do not underestimate the weight of the DP2K-E series projector. The projector weights approximately 53 kg (116.8 lb.) without lens.
Ensure that the pedestal on which the projector is installed is capable of supporting the complete load of the system. Minimum 4
adult persons are needed to carry the projector.
16
R5906693 DP2K-E SERIES 19/06/2015
Содержание DP2K-E series
