![background image](http://html1.mh-extra.com/html/barco/coronis-5mp-mammo/coronis-5mp-mammo_system-manual_3886855086.webp)
System manual Coronis 5MP
87
Inst
Inst
Inst
Inst
Installing the BarcoMed 5MP2F W
alling the BarcoMed 5MP2F W
alling the BarcoMed 5MP2F W
alling the BarcoMed 5MP2F W
alling the BarcoMed 5MP2F Windows XP
indows XP
indows XP
indows XP
indows XP
Display Driver
Display Driver
Display Driver
Display Driver
Display Driver
SPECIAL
SPECIAL
SPECIAL
SPECIAL
SPECIAL NOTE:
NOTE:
NOTE:
NOTE:
NOTE: Prior to installing the BarcoMed drivers you MUST
install the BarcoMed Display Controller(s), connect the CORONIS
display panel(s) to the card(s), and turn the CORONIS display
panel(s) on. Refer to the Hardware Installation section of this manual
for instructions on installing the BarcoMed Imaging Board(s) and
connecting them to the CORONIS display panel(s).
The following software installation instructions presume that Windows
XP is already installed on your system. If you need to install or
reinstall Windows XP on your system you must first remove the
BarcoMed Display Controller(s) and use a 3
rd
party VGA card and
VGA monitor during the Windows XP installation process.
Using the BarcoMed Product Installation Wizard
Using the BarcoMed Product Installation Wizard
Using the BarcoMed Product Installation Wizard
Using the BarcoMed Product Installation Wizard
Using the BarcoMed Product Installation Wizard
To install your BarcoMed 5MP2F Windows Display Controller Driver,
BARCO DPMS Screen Saver and CORONIS Rotation Service for the
first time, follow the steps below. If you are reinstalling the drivers or
installing a new driver release over an existing driver release, skip to
the step 7 on the next page:
1. Install the BarcoMed Display Controller(s) into your machine.
Please refer to the hardware installation guide that came with your
BarcoMed Display Controller(s) for more information.
2. Boot the machine and log in using an account with administrative
privileges.
3. Windows XP will do a thorough inspection of your system and will
announce that it has found new hardware. Please be patient as
this may take up to 5 minutes.
4. Close any informational balloons that Windows XP may open in
the lower right hand corner of the monitor.
5. Windows XP will automatically launch the “Found New Hardware
Wizard” (figure 61 on the next page). Click “Cancel”
“Cancel”
“Cancel”
“Cancel”
“Cancel” to exit the
Wizard.
BarcoMed software driver installation
Содержание Coronis 5MP Mammo
