![background image](http://html1.mh-extra.com/html/barco/coronis-5mp-mammo/coronis-5mp-mammo_system-manual_3886855102.webp)
System manual Coronis 5MP
103
Setting the Resolution of Your CORONIS Display Panel with
Setting the Resolution of Your CORONIS Display Panel with
Setting the Resolution of Your CORONIS Display Panel with
Setting the Resolution of Your CORONIS Display Panel with
Setting the Resolution of Your CORONIS Display Panel with
DualView Enabled
DualView Enabled
DualView Enabled
DualView Enabled
DualView Enabled
By default DualView is enabled when you install the BarcoMed
Windows XP driver. DualView is a Windows XP feature that allows a
dual headed display controller with a single graphics chip to display
two separate desktops, one for each monitor instead of a single virtual
desktop that spans across both monitors. If you wish to disable
DualView, you can do so through the Monitor Configuration settings of
the BarcoMed Driver Tab. Instructions for disabling DualView can be
found at the end of this chapter.
1. To set the resolution for your CORONIS display(s), right click on an
empty space of the desktop and select “Properties”
“Properties”
“Properties”
“Properties”
“Properties”.
2. Select the “Settings”
“Settings”
“Settings”
“Settings”
“Settings” tab (see figure 87 on the next page). Now
select the rect
rect
rect
rect
rectangle
angle
angle
angle
angle that represents the first CORONIS display
attached to the BarcoMed Display Controller you are working with.
SPECIAL NOTE:
SPECIAL NOTE:
SPECIAL NOTE:
SPECIAL NOTE:
SPECIAL NOTE: If the BarcoMed Display Controller is not running
VGA, the display may not be enabled yet. To enable the device
check
check
check
check
check the “Extend my W
“Extend my W
“Extend my W
“Extend my W
“Extend my Windows desktop onto this monitor”
indows desktop onto this monitor”
indows desktop onto this monitor”
indows desktop onto this monitor”
indows desktop onto this monitor”
checkbox. Do not click the “Apply”
“Apply”
“Apply”
“Apply”
“Apply” button at this time.
3. Click on the “Advanced”
“Advanced”
“Advanced”
“Advanced”
“Advanced” Button.
4. Select the “Adapter”
“Adapter”
“Adapter”
“Adapter”
“Adapter” tab and then click on the “List
“List
“List
“List
“List All Modes…”
All Modes…”
All Modes…”
All Modes…”
All Modes…”
button. Select the resolution and refresh rate that your CORONIS
display supports from the dialog box and click “OK”
“OK”
“OK”
“OK”
“OK”.
5. Click “OK”
“OK”
“OK”
“OK”
“OK” on the bottom of the Adapter Control Panel. If the
“OK”
“OK”
“OK”
“OK”
“OK” button on the bottom of the Adapter Control Panel is not
visible, press the “T
“T
“T
“T
“Tab Key”
ab Key”
ab Key”
ab Key”
ab Key” once and then press “Enter”
“Enter”
“Enter”
“Enter”
“Enter”. Your
high resolution display(s) should now synchronize and display the
Windows desktop.
6. Click “Y
“Y
“Y
“Y
“Yes”
es”
es”
es”
es” if asked, “Your desktop has been reconfigured. Do
you want to keep these settings?” Windows XP will only ask this
question for the first display on each BarcoMed Display Controller.
7. To set the resolution of the second CORONIS display attached to
the BarcoMed Display Controller you are working with, open the
“Display Properties Control Panel”
“Display Properties Control Panel”
“Display Properties Control Panel”
“Display Properties Control Panel”
“Display Properties Control Panel” again by right clicking on the
desktop and select “Properties”
“Properties”
“Properties”
“Properties”
“Properties”. Now select the “Settings”
“Settings”
“Settings”
“Settings”
“Settings” tab.
Enable this device by checking the “Extend my W
“Extend my W
“Extend my W
“Extend my W
“Extend my Windows
indows
indows
indows
indows
desktop onto this monitor”
desktop onto this monitor”
desktop onto this monitor”
desktop onto this monitor”
desktop onto this monitor” checkbox. Do not click the “Apply”
“Apply”
“Apply”
“Apply”
“Apply”
button at this time. Now repeat step 4 – 6 above.
S
S
S
S
Special note:
pecial note:
pecial note:
pecial note:
pecial note: The resolution for each display connected to a single
BarcoMed controller must be identical, including the refresh rate.
Repeat steps 1 – 7 to set the resolution for the displays on all the
BarcoMed Display Controller(s) installed in your system.
BarcoMed software driver installation
Содержание Coronis 5MP Mammo
