Banner DF-G3 Series, Инструкция по эксплуатации

Страница: 25 / 33

5 Specifications
Sensing Beam
DF-G3: Visible red, 635 nm
DF-G3IR: Infrared, 850 nm
Supply Voltage
10 V to 30 V dc Class 2 (10% maximum ripple)
Power and Current Consumption (exclusive of load)
Standard display mode: 960 mW, Current consumption < 40 mA at 24 V
dc
ECO display mode: 720 mW, Current consumption < 30 mA at 24 V dc
Supply Protection Circuitry
Protected against reverse polarity and transient overvoltages
Delay at Power-Up
500 milliseconds maximum; outputs do not conduct during this time
Output Configuration
CH1 = IO-Link, Push/pull
CH2 = PNP only output or input
Output Rating
100 mA maximum load each output (derate 1 mA per °C above 30° C)
100 mA max total load current for sensor
OFF-state leakage current: < 5 µA PNP at 30 V dc (N.A. push/pull);
ON-state saturation voltage: < 2 V
Required Overcurrent Protection
WARNING: Electrical connections must be
made by qualified personnel in accordance
with local and national electrical codes and
regulations.
Overcurrent protection is required to be provided by end product
application per the supplied table.
Overcurrent protection may be provided with external fusing or via
Current Limiting, Class 2 Power Supply.
Supply wiring leads < 24 AWG shall not be spliced.
For additional product support, go to
www.bannerengineering.com
.
Supply Wiring (AWG) Required Overcurrent Protection (Amps)
20 5.0
22 3.0
24 2.0
26 1.0
28 0.8
30 0.5
IO-Link Interface
Supports smart sensor profile: Yes
Baud rate: 38400 bps
Process data widths: 16 bits
IODD files: Provides all programming options of the display, plus
additional functionality
Output Protection
Protected against output short-circuit, continuous overload, transient
overvoltages, and false pulse on power-up
Construction
Black ABS/polycarbonate alloy (UL94 V-0 rated) housing, clear
polycarbonate cover
Connections
PVC jacketed 2 m (6.5 ft) 4-wire integral cable; or integral 4-pin M8/
Pico-style quick disconnect; or 150 mm (6 inch) cable with a 4-pin M12/
Euro-style quick disconnect; or 150 mm (6 inch) cable with a 4-pin M8/
Pico-style quick disconnect
Adjustments
3-way RUN/PRG/ADJ Mode Switch
2-way CH1/CH2 Switch
3-way +/SET/- Rocker Button
• Expert-style teaching (Two-Point and Dynamic TEACH, Light/
Dark/Window/Calibration SET)
• Manually adjust sensitivity (from "+" and "-" rocker button
only)
• Response Speed, TEACH Selection, Offset Percent, Auto
Thresholds, Delays/Timers, Display Readout, Gain Selection,
Factory Defaults (from top panel or remote input)
• Top panel interface lockout (from remote input only)
Indicators
Red 4-digit Display: Signal Level
Green 4-digit Display: Threshold
(In Program Mode, Red and Green displays are used for programming
menus)
Amber LED: Output conducting
Environmental Rating
IEC IP50, NEMA 1
Operating Conditions
Temperature: –10 °C to +55 °C (+14 °F to +131 °F)
Storage Temperature: –20 °C to +85 °C (–4 °F to +185 °F)
Humidity: 90% at +60 °C maximum relative humidity (non-condensing)
Certifications
Industrial
Control
Equipment
3TJJ
Response Speed
Description Response
Speed
Repetition Period Repeatability Cross-Talk
Avoidance
Energy Efficient Light
Resistance
Maximum Range,
Red22
Maximum Range,
IR85023
High Speed 500 µs 100 µs 100 µs No No 1200 mm 2400 mm
Fast 1000 µs 100 µs 150 µs Yes No 1500 mm 3000 mm
Standard 2 ms 100 µs 180 µs Yes Yes 1500 mm 3000 mm
Long Range 8 ms 100 µs 180 µs Yes Yes 1950 mm 3900 mm
Extra Long Range 24 ms 100 µs 180 µs Yes Yes 3000 mm 6000 mm
22 Excess gain = 1 (high sensitivity), opposed mode sensing. PIT46U plastic fiber used for visible LED models.
23 Excess gain = 1 (high sensitivity), opposed mode sensing. IT.83.3ST5M6 glass fiber used for IR models.
DF-G3 Long Range Expert Dual Display Fiber Amplifier with Dual Discrete Outputs and IO Link
www.bannerengineering.com - Tel: + 1 888 373 6767 25