Bandit ZT1844, Инструкция по эксплуатации и каталог запасных частей

Страница: 37 / 102

Bandit
35 Copyright 12/18
MODEL ZT1844
GENERAL RULES FOR TENSIONING
Pump Drive Belt
1. Locate the center of the span between sheaves.
2. Push­or­pull­down­on­the­belt­until­the­belt­has­deflected­0.18”­(4.5­mm).
3. Record push or pull down force. The force should be 5.5 - 5.9 lbs (2.5 - 2.7 kg) for a new belt and
4.7 - 5.1 lbs (2.1 - 2.3 kg) for a used belt.
4. Adjust the belt tension if the force falls outside of this range.
5. If adjustment is needed, loosen both pump mount bolts.
6. Adjust­the­pump­to­achieve­the­required­force­and­deflection
7. Tighten the pump mount bolts.
BELT TENSION
Pump­Drive­belts­maximum­of­0.18”­(4.5­mm)­deflection
with 5.5 - 5.9 lbs. (2.5 - 2.7 kg) of force.
For­used­belts,­maximum­of­0.18”­(4.5­mm)­deflection
with 4.7 - 5.1 (2.1 - 2.3 kg) lbs. of force.
YES NO
BELT
SHEAVE
WORN BELT
YES NO
YES NO
BELT
SPACE
GOOD BELT
SHEAVE
BELT
SHEAVE
WORN SHEAVE
Worn or misaligned belts and sheaves in the power train
causes belt slippage, thus power loss. Keep the power
train working for you, not against you, by checking for
needed adjustment or replacement.
ANGULAR MISALIGNMENT
PARALLEL MISALIGNMENT
M
M
M
M
BELT TENSION GAUGES
SINGLE BARREL GAUGE
(UP TO 30 lbs.) 900-1919-23
DOUBLE BARREL GAUGE
(UP TO 66 lbs.) 900-1917-02
TRIPLE BARREL GAUGE
(UP TO 90 lbs.)
900-1919-67
FIVE BARREL GAUGE
(UP TO 165 lbs.) 900-1919-66
DANGER
!
Before attempting any type of maintenance, disengage clutch or cutter wheel engagement, wait for the
­cutter­wheel­to­come­to­a­complete­stop,­position­and­lock­the­cutter­wheel­in­the­transport­position,­turn­off­
engine, remove the ignition key, make sure the ignition key is in your possession, disconnect the battery, and
install the cutter wheel lock pin.
Do not over tighten the hydraulic pump belt. For best results use a good belt tension tester. Most all pump
failures result from too much side load on the pump shaft. Too much belt tension is very easy to detect inside
a failed pump. Pumps with this condition will not be covered under warranty.
DO NOT IGNORE THIS MAINTENANCE RULE!
New­belts­stretch­very­soon­and­must­be­adjusted­several­times­in­the­first­few­hours­of­operation.­Adjust­
after one hour of operation, then every four hours until the belts quit stretching.
MAINTENANCE
1. Check­tensioning­during­the­first­2­through­48­hours­of­run-in­operation­especially.
2. Over tensioning or under tensioning shortens belt and bearing life.
3. Keep belts free from foreign materials that may cause the belt to slip.
4. Make V-drive inspection on a periodic basis. Never use belt dressing as this will damage the belt and
cause early failure.
5. Belts should never be forced over the sheave. Allow enough room for belts to slip on.
6. Always make sure sheaves are aligned properly.