background image

P. 22 - Communication status  - LEDs - Front LEDs 

    

 Guard

N

  

Alarm 

 

Internal failure

 
       This red LED is on as long as 

BANDIT 

is in guard mode.

             

 
       This red LED is on from the moment 

BANDIT 

switches to alarm mode until the unit is

       put out of guard mode through the guard input [Grdin] or an optional remote control.
       This LED blinks as long as the unit is switched into panic mode
  
       

- This red LED blinks (~ 1 Hz) as long as 

BANDIT 

detects one or more internal failures. The 

unit practically checks continuously on possible internal failures. 
Check list of possible internal failures:

4

the glass fuse F2 (500 mA) which secures [Supply] 12 V power supply is interrupted

4

the heat exchanger can not reach the required temperature due to a broken element

       and/or the over temperature fuse has blown.

4

the glass fuse F3 (6.3 AT) which functions as battery fuse is interrupted.

4

the charge of the connected battery  is too low (bad battery or no battery present).

4

the revs of the internal fan aren’t right

4

the environmental temperature of the HY-3 pack is above 50°C.

4

the MCU measures unreal values or value jumps on one or more of its sensors, which

        indicates broken sensor(s).

- This  red LED blinks fast (~ 2 Hz) as long as 

BANDIT 

detects one or more adjustments, 

which are no real technical failures, but have influence on the normal operational 
behaviour of the fog generator:

4

”‘Red jump” isn’t plugged in.

4

A "Control Box" switch is still 

ON

.

4

The presence of a wrong type of HY-3 pack.

 

HY-3 pack 

(

HY-3 pack 

liquid reserve

)

 
       With a charged 

HY-3 pack,

 

BANDIT 

has 1.4 litre of 

HY-3

 liquid.

       During a fog expulsion, approximately 28 ml of fluid is consumed each second.
       So basically, there is a total of ~ 50 seconds of fog expulsion available. 
       This LED starts blinking as soon as there is less than 15 seconds of fog ejection time 
       available.       
       If this red HY-3 LED blinks, the 

HY-3 pack

 has to be replaced. See page 26.

       The actual fog fluid level can always be read off from the Control Box. See page 19.    

       As long as 

BANDIT 

is in guard mode, this LED will be off. This way the unit never will reveal

       a possible shortage of fog fluid, through its front panel, to the outside world. 

  
       

BANDIT

 240 DB 

v.206

Содержание 240 DB



































Отзывы:

Похожие инструкции для 240 DB