B&D Roll-A-Door 2 Series Скачать руководство пользователя страница 7

Страница: 7 / 16

1.5 parts checklist

1.6 initial calculations

a)  Measure the opening width of garage.
b)  Measure the door curtain width.
c)  Calculate over lap for each side:

door width - opening width : 2 = over lap

d) Mark the line for the edge of door curtain (over lap) on each side of the opening.

Fig: 1.5.1

SERIES 2 ROLL-A-DOOR

R2F & R2I

R2L & R2W

ITEM DESCRIPTION

QTY

ROLLED PLASTIC WRAPPED DOOR

BRACKETS, LEFT AND RIGHT HANDED

DOORS GUIDES LEFT AND RIGHT HANDED

STEEL LOCKING BARS

SMALL PARTS BAG CONTAINING

BOTTOM RAIL STOPS AND SCREWS

FACEPLATE AND LOCK ASSEMBLY

MUSHROOM HEAD SCREWS FOR LOCKING BAR

LOCKING BAR COVERS

LOCKING BAR RETAINER

"U" BOLTS

AXLE / BRACKET SADDLES

NUTS FOR "U" BOLTS

SMALL WASHERS (DOOR SIZE DEPENDENT)

8-12

LARGE WASHERS

tip

• Standard Series 2 doors

= 50mm (minimum) overlap each side

Roll-A-Door

Series 2 installation instructions

Содержание Roll-A-Door 2 Series

















Результаты поиска

Содержание Roll-A-Door 2 Series

Отзывы:

Похожие инструкции для Roll-A-Door 2 Series

Бренды по названию

Популярные бренды

B&D Roll-A-Door 2 Series, Руководство по установке

Результаты поиска

Содержание Roll-A-Door 2 Series

Отзывы:

Похожие инструкции для Roll-A-Door 2 Series

Бренды по названию

Популярные бренды