background image

6 - 8 Fiveways Boulevard, Keysborough, VIC, Australia 3173           
P: 1300 133 944      E: [email protected]      
W: www.automatictechnology.com.au

B&D Doors is a division of B&D Australia Pty Ltd 

ABN 25 010 473 971

B&D Doors, 34-36 Marigold St, Revesby, NSW, 2212
P: 13 62 63 

E: [email protected]

W: www.bnd.com.au

© Nov 2018 Automatic Technology (Australia) Pty Ltd. All rights reserved. No part of this document may be reproduced without prior permission. In an ongoing 

commitment to product quality we reserve the right to change specification without notice. E&OE.

Symptom

Possible cause

Remedy

Door stops or moves very slowly 

under battery power

Batteries may be weak or have 

no charge

Connect mains power and allow the batteries 

to charge. This may take 24 - 48 hours to reach 

maximum charge capacity.

Door will not operate when 

mains power is disconnected.

Batteries / charger board may 

not be connected properly.

Check wiring.

Batteries may have no charge

Connect mains power and allow the batteries 

to charge. This may take 24 - 48 hours to reach 

maximum charge capacity.

Faulty Charger board

Disconnect the charger board from batteries and 

control board. Check voltage of the charger board. 

Voltage should be approximately 27.5V.

Faulty Batteries

Disconnect the batteries from the charger board. 

Check the voltage of the each battery. Voltage 

should not drop below 10V.

Troubleshooting

Maintenance

To ensure a long trouble free life for your battery backup it is recommended you run the testing procedure on a monthly basis. 

Batteries should not need replacing for 4 - 5 years.

Testing Procedure:

a.  Press the transmitter to activate the opener. 

b. Whilst the door / gate is in motion disconnect power. The door / gate should complete the cycle as normal.

c.  Wait for the door / gate to finish is travel.

d. Press the transmitter to activate the opener.

e.  Whilst the door / gate is in motion reconnect power. If the door / gate stopped or moved very slosly under battery power, 

ensure mains power is connected for 24 - 48 hours to recharge the batteries. Test the opener again under battery power to 

ensure batteries are working effectively.

Warranty

This warranty is to be read in conjunction with the owner’s copy of 

the opener installation instruction.

WARRANTY

ACCESSORIES

1 year

Содержание Automatic Technology Battery Backup Gen 2 Kit









Отзывы: