B&B Electronics Zlinx ZP Series Скачать руководство пользователя | Manualshive

Страница: 47 / 49

background image

Manual Documentation Number: ZPXXx-XXXXx-MR-0812

47

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 –

www.bb-elec.com

B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 –

www.bb-europe.com

SM (Sleep Mode) Command

<Sleep Mode (Low Power)>
Set/Read Sleep Mode
Settings. By default, Sleep
Mode is disabled and the
module remains continually
active.

SM Command allows the
module to run in a lower-power
state and to be configured in
one of eight settings.

Cyclic Sleep settings wake the
module after the amount of
time designated by SM
Command. If the module
detects a wake-up initializer
during the time it is awake, it
will synchronize with the
transmitter and start receiving
data after the wake-up
initializer runs its duration.
Otherwise, it returns to Sleep
Mode and continues to cycle in
and out of inactivity until the
Wake-up Initializer is detected.
If a Cyclic Sleep setting is
chosen, the ST, LH and HT
parameters must also be set
as described in the “Sleep
Mode” section of this
manual.

ST (Time before Sleep)
Command

<Sleep Mode (Low Power)>
Set/Read the period of time in
which the module remains
inactive before entering into
Sleep Mode. For example: If
the ST parameter is set to
0x64 (100 decimal), the
module will enter into Sleep
mode after 10 seconds of
inactivity (no transmitting or
receiving). This command can only be used if Cyclic Sleep or Serial Port Sleep Mode
settings have been selected using the SM command.

AT Command: ATSM

Binary Command: 0x01

Parameter Range: 0

– 8

Parameter

Configuration

0

Disabled

1

Pin Sleep

2

Serial Port Sleep

3

Cyclic 0.5 second sleep

(Module wakesevery 0.5

seconds)

4

Cyclic 1.0 second sleep

5

Cyclic 2.0 second sleep

6

Cyclic 4.0 second sleep

7

Cyclic 8.0 second sleep

8

Cyclic 16.0 second sleep

Default Parameter Value: 0

Number of bytes returned: 1

Related Commands:
Pin Sleep

– PC (Power-up Mode), PW (Pin Wake-

up)

Serial Port Sleep

– ST (Time before Sleep)

Cyclic Sleep

– ST (Time before Sleep), LH (Wake-

up Initializer Timer), HT (Time Before Wake-up
Initializer), PW (Pin Wake-up)

AT Command: ATST

Binary Command: 0x02

Parameter
Range:

0x10

– 0xFFFF [x 100

milliseconds]

Default Parameter Value: 0x64 (100 decimal)

Number of bytes returned: 2

Related Commands: SM (Sleep Mode), LH
(Wake-up Initializer Timer), HT (Time before
Wake-up Initializer)

«
...
45
46
47
48
49
»

Содержание Zlinx ZP Series


















































Отзывы:

Нет отзывов

Похожие инструкции для Zlinx ZP Series

LUNCHBOX LB-100

Бренд: Sangean Страницы: 1

Бренд: Sprint Страницы: 78

Бренд: Disney Страницы: 10

Бренд: iCES Страницы: 6

SureCross DX80ER M-H Series

Бренд: Banner Страницы: 3

Бренд: TP-Link Страницы: 98

Бренд: Patton electronics Страницы: 20

Бренд: Cobra Страницы: 35

Бренд: Multitech Страницы: 49

Бренд: Atel Страницы: 9

Бренд: Uniden Страницы: 104

Бренд: Sigrand Страницы: 42

Бренд: Raveon Страницы: 32

Бренд: Intermec Страницы: 8

Cobra CB 29 LX LE

Бренд: Giant Страницы: 6

Бренд: Garmin Страницы: 43

Бренд: axing Страницы: 4

Бренд: Vertex Standard Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды