B&B Electronics Zlinx ZP Series Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 49

background image

42

Manual Documentation Number: ZPXXx-XXXXx-XR-0812

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 –

www.bb-elec.com

B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 –

www.bb-europe.com

PK (RF Packet Size)
Command

<Serial Interfacing> Set/Read
the maximum size of the RF
packets sent out a transmitting
module. The maximum packet
size can be used along with
the RB and RO parameters to
implicitly set the channel dwell
time.

Changes to this parameter
may have a secondary effect on the RB (Packet Control Characters) parameter. RB
must always be less than or equal to PK. If PK is changed to a value less than the
current value of RB, RB is
automatically lowered to be
equal to PK.

PW (Pin Wake-up) Command

<Sleep (Low Power)> Under
normal operation, a module in
Cyclic Sleep Mode cycles from
an active state to a low-power
state at regular intervals until
data is ready to be received. If
the PW Parameter is set to 1,
SLEEP (pin 2) can be used to
wake the module from Cyclic
Sleep. If the SLEEP pin is de-
asserted (low), the module will
be fully operational and will not
go into Cyclic Sleep. Once
SLEEP is asserted, the
module will remain active for the period of time specified by
ST (Time before Sleep) Command and will return to Cyclic Sleep Mode (if no data is
ready to be transmitted). PW Command is only valid if Cyclic Sleep has been
enabled.

RB (Packetization
Threshold) Command

<Serial Interfacing> RF
transmission will commence
when data is in the DI Buffer
and either of the following
criteria are met:
   RO times out on the UART
  receive lines
  (ignored if RO = 0)
   RB characters have been
  received by the UART
  (ignored if RB = 0)

If PK is lowered below the value of RB; RB is automatically lowered to match PK.

AT Command: ATPK

Binary Command: 0x29 (41 decimal)

Parameter Range: 0

– 0x100 [Bytes]

Default Parameter Value: 0x40 (64 decimal)

Number of bytes returned: 2

Related Commands: RB (Packetization
Threshold), RO (Packetization Timeout)

Minimum Firmware Version Required: 4.30

AT Command: ATPW

Binary Command: 0x1D (29 decimal)

Parameter Range: 0

– 1

Parameter

Configuration

0

Disabled

1

Enabled

Default Parameter Value: 0

Number of bytes returned: 1

Related Commands: SM (Sleep Mode), ST (Time
before Sleep)

Minimum Firmware Version Required: 4.22

AT Command: ATRB

Binary Command: 0x20 (32 decimal)

Parameter Range: 0

– 0x100 [bytes](Maximum

value equals the current value of PK Parameter
(up to 0x100 HEX (800 decimal))

Default Parameter Value: 1

Number of bytes returned: 2

Related Commands: PK (RF Packet Size), RO
(Packetization Timeout)

Minimum Firmware Version Required: 4.30

«
...
40
41
42
43
44
...
»

Содержание Zlinx ZP Series


















































Отзывы:

Нет отзывов

Похожие инструкции для Zlinx ZP Series

COMSPHERE 3800PLUS

Бренд: Paradyne Страницы: 4

Бренд: Paradyne Страницы: 16

Бренд: Paradyne Страницы: 2

Бренд: Scott Страницы: 14

P3 Player FM RADIO EARPHONE

Бренд: X-Micro Страницы: 2

Бренд: Jensen Страницы: 12

Бренд: Radio Shack Страницы: 12

Бренд: Easy Listener Страницы: 17

Бренд: ATO Страницы: 18

Бренд: SANG Страницы: 20

Бренд: NAPCO Страницы: 16

Бренд: Audiovox Страницы: 62

Бренд: S&C Страницы: 4

Бренд: Abocom Страницы: 20

Бренд: Vertex Standard Страницы: 6

Бренд: FW Страницы: 12

Бренд: Zte Страницы: 39

Бренд: Technoline Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды