Bandai Namco Time Crisis 5 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 194

Bandai Namco Time Crisis 5 Скачать руководство пользователя страница 32

32

7. Operation

●

Should an abnormality occur, turn off the power switch immediately to stop operations. Then, be sure to
disconnect the power cord plug from the outlet. Operating the machine while the abnormality persists
may result in fire or accident.

●

Dust accumulating on the power cord plug may result in fire. Inspect the plug regularly and remove any
dust.

●

Fully insert the power cord plug into the outlet. Poor contact may generate heat and result in fire or
burns.

●

Before operating the machine, be sure to check that installation has been performed according to the
instructions and specified procedures in this Operation Manual (see P-24 "5. Delivery and Installation
Conditions"). Failure to install the machine normally may result in fire, electric shock, injury or
malfunction.

●

The warning labels attached to the machine contain important information to ensure safety. Be sure to
observe the following.

●

In order to ensure that the warning labels attached to the machine are always clearly visible, install the
machine in an appropriate location with ample illumination and keep the labels clean at all times. Also
make sure that the labels are not hidden by other machines or objects.

●

Do not remove or alter the warning labels.

●

If a warning label becomes excessively dirty or damaged, replace it with a new one. To order warning
labels, contact your distributor.

●

In order to ensure safe use of the machine, be sure to perform the pre-operation inspection (P-34 "7-4
Pre-operation Inspection") and service (P-84 "8B. Service") described in this Operation Manual.

●

Omitting these inspections or service may result in an accident.

WARNING

7-1 People Who Should Not Play the Game

●

In order to ensure the safety of players, be careful not to let people play under the following conditions.
Failure to do so may result in an accident.

•

People who are sensitive to light such as strobe lights

•

People whose behavior is against what is described on the warning labels on this machine

•

People who are sensitive to light such as strobe lights

•

People whose behavior is against what is described on the warning labels on this machine

WARNING

«
...
30
31
32
33
34
...
»

Содержание Time Crisis 5



































































































































































































Отзывы:

Нет отзывов