Bame Delma POLARIS 4 Скачать руководство пользователя | Manualshive

Страница: 8 / 24

background image

1. Power the control board.
2. Memorize the remote as parameter C1 page 16

3. Press P1 and P2 simultaneously for three seconds to begin programming the board.

4. Letter A appear on the display.

5. Press P2 to confirm.

6. The number 1 appear on the display.

7. Push the button of the remote memorized to start opening gate

9. Please wait that the gate opens completely. The reclosing is automatic.

10. The gate start for the reclosing.
Push the button of the remote memorized when you want start the slowing down.

Programming the work time

- 8 -

8. Push the button of the remote memorized when you want start the slowing down

11. Please wait the complete closing of the gate.
Please wait that the board goes out automatically from the programming.

«
...
6
7
8
9
10
...
»

Содержание Delma POLARIS 4

























Отзывы:

Нет отзывов

Похожие инструкции для Delma POLARIS 4

Бренд: Zap Страницы: 80

Бренд: Zero Страницы: 16

Бренд: PowerTech Страницы: 20

76380 - Classic Chrome Heavyweight Can...

Бренд: Hamilton Beach Страницы: 5

Бренд: Jaytech Страницы: 19

Бренд: CornellCookson Страницы: 24

Бренд: Sentex Страницы: 20

Бренд: MPC Страницы: 8

Бренд: Garage Smart Страницы: 41

Бренд: Zero Страницы: 12

Бренд: Daspi Страницы: 12

Бренд: CAME Страницы: 36

Бренд: V2 Страницы: 88

Бренд: V2 Страницы: 92

GOLD1200D Series

Бренд: V2 Страницы: 172

Бренд: tau Страницы: 16

Бренд: Calimet Страницы: 24

Бренд: Vimar Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды