Bame Delma POLARIS 4 Скачать руководство пользователя | Manualshive

Страница: 19 / 24

background image

- 19 -

Additional features

This parameter is used to check if the clutch has been detected or not, during the setting of the work time.

The additional features are not necessary for normal operations, but they are very useful in case of parti-
cular installations.

1. Press P1 and P2 simultaneously for three seconds

to begin programming the board.

2. Letter A appear on the display. Scroll the menu with P1

until letter F appears on the display.
Press P2 to confirm.

3. You should see 1 on the display.

Press P2 to confirm.

4. If on display appear the number 0,the clutch
is not enabled.

If on display appears one 1 the encoder is activated.

5. Press P2 to get out

Parameter F1: display clutch status (ON/OFF)

ATTENTION!!!!!! This parameter allows to visualize only the encoder state, not to change it

«
...
17
18
19
20
21
...
»

Содержание Delma POLARIS 4

























Отзывы:

Нет отзывов

Похожие инструкции для Delma POLARIS 4

Swing L 300 MGLSK

Бренд: Merlin Страницы: 4

Бренд: D.A.C.E Страницы: 14

SeceuroGlide Compact

Бренд: SWS Страницы: 12

Бренд: SCS Sentinel Страницы: 88

Home Motion Dexxo Compact RTS

Бренд: SOMFY Страницы: 36

Бренд: CAME Страницы: 2

Бренд: CAME Страницы: 36

Бренд: APRI Страницы: 33

Бренд: Chamberlain Страницы: 88

Бренд: Chamberlain Страницы: 180

Titano QK-T4000

Бренд: quiko Страницы: 9

Бренд: CAME Страницы: 20

Бренд: CAME Страницы: 52

Doormax FS 1000

Бренд: KRUZIK Страницы: 64

FROG SERIES FROG-A 24V

Бренд: CAME Страницы: 12

Бренд: CAME Страницы: 16

Бренд: CAB Страницы: 60

Бренд: XPOtool Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды