ENGLISH
26 / 60
0006160032_201711
FIRST PIPELINE FILLING UP
After checking that the protective plastic caps on the pump fittings
have been removed, proceed as follows:
•
Turn to "on" position the switch -1 on the mimic panel of the burner
making sure that the thermostat line switch -2 is set to "O".
•
Make sure the line voltage is the same as indicated in the
identification plate of the burner.
DANGER / CAUTION
To positively determine the direction of rotation, wait until the
fan turns very slowly because it is quite easy to misinterpret the
direction of rotation.
•
The fan rotation direction can be checked also by looking at the fan
through the inspection hole located on the back of the scroll.
•
If it is necessary to change the direction of rotation, invert two
phases of the line input terminals (L1_L2_L3)
•
To start up the motor, close the remote control switch manually
(by pressing on the mobile part) for a few seconds and watch the
sense of rotation of the fan.
•
Detach, if already attached, the flexible hoses from the intake and
return pipes.
• Dip the end of the suction hose into a vessel containing either
lubrication oil or diesel (do not use low viscosity products such as
petrol, kerosene, etc.).
•
Now press key (9) on the control panel to start the motor and the
pump.
DANGER / CAUTION
Pump operating at 2800 r.p.m. must not work dry otherwise
they will jam (seizure) within a very short time.
•
Attach the flexible hose to the intake pipe and open any gate valves
fitted on this pipe and any other shut-off element on the fuel pipes.
•
Press button (9) again to start up the pump that extracts the fuel
from the tank.
•
When you see the fuel coming out of the return line (not yet
connected), stop.
DANGER / CAUTION
If the pipe is long, it may be necessary to bleed the air out
through the cap; if the pump is not fitted with a cap, remove the
pressure gauge connector cap.
•
Connect the return flexible hose to the return pipe and open the
gates fitted on this pipe. Now the burner is ready for lighting up.
1
2
10
3
4
9
11
5
display_TBML_ME
1 ON / OFF main switch.
2 Thermostatic line switch
3 Display
4 Unlock or RESET button
5 Fuse.
9 Fuel fill button
10 Fuel selector switch
11 Programming keypad
Содержание TBML 120 ME
