BaltGaz BaltGaz NEVALUX-8224 Скачать руководство пользователя страница 28

Руководство для технического персонала 

32

 

 

 

5)

 

The electronic board supplies voltage to the fan’s electrical motor  28.  The fan starts operating (it can be 
heard). By means of air flow a pressure difference is created in the air pressure switch  27. A signal about 
draught presence comes to the electronic board 11. If there is no signal, the boiler’s launching stops; 

6)

 

 A pause for combustion chamber ventilation is held (it is necessary for gas removal in case of previous 
failed launching)  

7)

 

 The ignition transformer  12 transfers high voltage to the ignition plug 5 on the signal of the electronic 
board 11 in~ 10 sec. (a sound of current discharge  can be heard); 

8)

 

 The electronic board 11 provides a signal   for opening the gas valve in the gas supply regulator 9, and 
gas comes to the burner block 4; 

9)  If  ignition  happened  (if  the  casing  is  removed,  you  can  see  the  flame  through  the  glory-hole),  an 

ionization plug 6 sends a signal to the electronic board about successful ignition. If there is no signal from the 
ionization plug, the electronic board 11 repeats the procedure of boiler’s launching from the beginning. There 
are 2 consecutive launching attempts taken. If both attempts fail, the electronic board stops ignition; 

 

10)The  electronic  board  11changes  voltage  in  the  modulator  coil  of  gas  supply  regulator  9.The  gas 
supply regulator increases gas supply to the burner block 4 up to maximal power in order to quickly 
warm the heat carrier in the heating system up to the set temperature; 

11)The electronic board compares the signal from the CH temperature sensor  16 with the value set by the 
user with the buttons К3 and К4 (see p. 3.1, page 8).  If the difference of set temperatures is more than 1

 

°С, the electronic board 11changes voltage on the gas supply regulator 9 in order to change gas supply to 
the burner block in accordance with the CH’s requirement.  

13.4.2

 

Boiler’s operation in DHW mode: 

1)

 

DHW  flow  sensor  23  sends  a  signal  (see  p.  13.1,  page  27)  about  presence  of  water  flow  in  DHW 
supply circuit; 

2)

 

The electronic board 11 checks the 3 way valve’s position; 

3)

 

If the 3 way valve18 is in the position, corresponding to the DHW mode, the electronic board supplies 
voltage  to  its  electrical  motor  19.  The  electrical  motor  moves  the  3  way  valve18  to  the  position 
corresponding to the DHW supply mode. As a result the heat carrier from the primary heat exchanger 
is directed to the secondary heat exchanger 3, providing the DHW supply mode this way; 

4)

 

 The electronic board provides voltage to the pump 7 (voltage presence on the pump’s terminals can 
be checked with a tester).The pump starts operating (the sound of operating pump can be heard);  

5)

 

The electronic board inquires the air pressure switch 27, its contacts must be opened. If the contacts 
are closed, the boiler’s launching stops; 

6)

 

 The electronic board provides voltage to the fan’s electric motor 28. The fans starts operating (it can 
be heard). By means of air flow a pressure difference is created in the air pressure switch  27. A signal 
about draught presence comes to the electronic board 11. If there is no signal, the boiler’s launching 
stops; 

7)

 

A  pause  for  combustion  chamber  ventilation  is  held  (it  is  necessary  for  gas  removal  in  case  of 
previous failed launching); 

8)

 

The  ignition  transformer    12  transfers  high  voltage  to  the  ignition  plug  5  on  the  signal  of  the 
electronic board  in~ 10 sec. (a sound of current discharge  can be heard); 

9)

 

The electronic board  provides a signal   for opening the gas valve in the gas supply regulator 9, and 
gas comes to the burner block 4; 

10)

 

If ignition happened (if the casing is removed, you can see the flame through the glory-hole), 

the  ionization  plug  6  sends  a  signal  to  the  electronic  board  about  successful  ignition.  If  there  is  no 
signal from the ionization plug, the electronic board  repeats the procedure of boiler’s launching from 
the beginning. There are 2 consecutive launching  attempts taken. If both attempts fail, the electronic 
board stops ignition; 

11)

 

The electronic board changes voltage in the modulator coil of gas supply regulator 9.The gas 

supply regulator increases gas supply to  the  burner block    up to  maximal power in  order to  quickly 
warm the water in the DHW supply system up; 

12)

 

The electronic board compares the signal from the DHW temperature sensor  17 with the value 

set by the user with the buttons К1 and К2 (see p. 3.1, page 8).  If the difference of set temperatures is 
more than 1

 

°С, the electronic board changes voltage on the gas supply regulator  in order to change 

gas supply to the burner block in accordance with the CH’s requirement. 

13.4.3 Boiler’s operation in combined mode 

In this mode the DHW supply has a priority over heating. In case of no water flow on the DHW supply 

line the boiler operates in the heating mode.  

If there is water flow in the DHW supply line: 

-

 

DHW  flow  sensor  23  actuates  (see  p.  13.1,  page  27).  A  signal  about  presence  of  water  flow  in  the 
DHW is sent to the electronic board; 

-

 

The electronic board supplies voltage to the electric motor 19 of the  3 way valve18

.

 

The  electric  motor  moves  the

 

3  way  valve18.    As  a  result  the  heat  carrier  from  the  primary  heat 

exchanger is directed to  the secondary heat  exchanger   3, providing the DHW priority this way  (water 
inlet into the heating system is blocked during all the period of water withdrawal in the DHW system). 

When  water  flow  in  the  DHW  line  stops  (there  is  no  signal  from  DHW  flow  sensor  23)  the  boiler  is 

rendered to the heating mode ( the electronic board supplies voltage to the electric motor and it moves the 3 
way valveto the position for the heating mode). 

Содержание BaltGaz NEVALUX-8224

























































Отзывы: