Balogh MOL81 485 1312 Скачать руководство пользователя | Manualshive

Страница: 9 / 20

background image

MOL81 485 1312/MOL81 485 1337

MOL81 485 1312-MOL81 485 1337-UM-1.4-EN

9/20

5 CONNECTION TO HOST

5.1 Introduction

The reader is connected to a host using a serial asynchronous two-wire RS 485 link. Other devices can be

connected on the same link.

5.2 Transmission characteristics

Baudrate and format are fixed:

19200 bits/s

8 data bits, no parity, 1 stop bit

RS-485

MOL81

HOST

«
...
7
8
9
10
11
...
»

Содержание MOL81 485 1312





















Отзывы:

Нет отзывов

Похожие инструкции для MOL81 485 1312

Бренд: Hand Held Products Страницы: 20

Бренд: Agri-Fab Страницы: 1

Бренд: Postech Страницы: 41

AquaTronics MS250

Бренд: ASA Electronics Страницы: 5

Бренд: Access security product Страницы: 10

MultiReader PER3664BC

Бренд: Prestigio Страницы: 108

SV 517 RDS/BT DAB

Бренд: Majestic Страницы: 13

PAN MOBIL ID PM ECCO+

Бренд: Feig Electronic Страницы: 24

Бренд: Socket Страницы: 75

Бренд: Aladdin Страницы: 6

Бренд: Land Pride Страницы: 32

Бренд: Newland Страницы: 22

Бренд: Clas Ohlson Страницы: 4

Powe X Change PXCUSS-018

Бренд: Ozito Страницы: 6

Бренд: IMS Страницы: 19

Бренд: JVC Страницы: 59

KD-AR760 - Arsenal CD Receiver

Бренд: JVC Страницы: 105

Бренд: JVC Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды