Balogh MOL81 485 1312 Скачать руководство пользователя

Страница: 16 / 20

MOL81 485 1312/MOL81 485 1337

MOL81 485 1312-MOL81 485 1337-UM-1.4-EN

16/20

8 CONNECTORS

The connectors used belong to the SOURIAU UTO series, size 12, with 8 pins, IP67 watertight, with EMI-
compatible shielding. These are metallic circular connectors with bayonet coupling.

8.1 Connector on case

The case connector is a panel-mount 8-pin plug with jam-nut receptacle.

References:

Plug: UTO71208PH

Pins: RM20M12E8K

The pins have a diameter of 1.6mm.

The table shows the pin assignments:

External view of connector

(rear-view of cable assembly connector)

The two-wire serial link uses pins C and F.

For a 120ohm line termination, pins B and E can be connected together if necessary for RS485 long cable

Figure 8-1: Connection diagram for normal RS485 operation with line termination

(A)

(B)

(COM)

Controller or PC

(A)

(B)

MOL81

* E

)

(Output "

PRESENCE

(0V)

RS485

Signal/Name

Power (+ 24V DC)

Line termination 120ohms (can be connected to E)

RS485 +

0 V

Line termination 120ohms (can be connected to B)

RS485 -

Output : PRESENCE

Output : 125 kHz OK

(Output "125 kHz OK")

Содержание MOL81 485 1312





















Результаты поиска

Содержание MOL81 485 1312

Отзывы:

Похожие инструкции для MOL81 485 1312

Бренды по названию

Популярные бренды

Balogh MOL81 485 1312, Руководство пользователя

Результаты поиска

Содержание MOL81 485 1312

Отзывы:

Похожие инструкции для MOL81 485 1312

Бренды по названию

Популярные бренды