manualshive.com logo in svg

Baldor GLC10, Инструкция по установке и эксплуатации

Поделиться
Скачать
Baldor GLC10 Скачать руководство пользователя страница 82

A‐4 Series GLC

MN2408

Silencers

Refer to enclosure procedure to install silencer when enclosure is present.
Industrial Silencer for Open Skid Mount Units - Provides silenced exhaust for up to 11 dBA
sound attenuation.  Kit includes engine adapters, flex pipe, clamps, silencer, and rain cap.
Critical Silencer for Open Skid Mount Units - Provides silenced exhaust for up to 18 dBA sound
attenuation.  Kit includes engine adapters, flex pipe, clamps, silencer, and rain cap.

Figure A‐4  

Industrial Silencer
GLCIS-3SU-

GLC10-25

GLCIS-4SU-

GLC30-45

GLCIS-6SU-

GLC60-90

GLCIS-7SU-

GLC100-105

Critical Silencer
GLCCS-4SU-

GLC30-45

GLCCS-6SU-

GLC60-90

GLCCS-7SU-

GLC100-105

Silencer

 (refer to Figure A‐4 for specific details)

1.

Attach the Silencer to the Exhaust Output of the engine, refer to Figure B-4.

2.

Use correct size clamp to attach extension pipe to Exhaust Output pipe from engine.

3.

Be sure the Extension pipe fits securely over Exhaust Output pipe so that no exhaust
leaks can occur.

Содержание GLC10



















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды