Balboa TP800 series Скачать руководство пользователя | Manualshive

Страница: 19 / 22

background image

40985_F

12-08-11

19

Manufactured under one or more of these patents. U.S. Patents: 5332944, 5361215, 5550753, 5559720, 5,883,459, 6253227, 6282370, 6590188, 6976052, 6965815, 7030343, 7,417,834 b2,
Canadian Patent: 2342614, Australian patent: 2373248 other patents both foreign and domestic applied for and pending. All material copyright of Balboa Water Group.

Sensor-Related Messages

Miscellaneous Messages

Sensors are out of sync – M015

The temperature sensors MAY be out of sync by 2°F or 3°F. Call for Service.

Sensors are out of sync -- Call for service* – M026

The temperature sensors ARE out of sync. The fault above has been established for at least 1 hour.
Call for Service.

Sensor A Fault, Senor B Fault – Sensor A: M031, Sensor B: M032

A temperature sensor or sensor circuit has failed. Call for Service.

Communications error

The control panel is not receiving communication from the System. Call for Service.

Test software installed

The Control System is operating with test software. Call for Service.

°F or °C is replaced by °T

The Control System is in Test Mode. Call for Service.

* This message can be reset from the topside panel.

M0XX numbers are Message Codes. See Page 13.

«
...
17
18
19
20
21
...
»

Содержание TP800 series























Отзывы:

Нет отзывов

Похожие инструкции для TP800 series

Бренд: ABB Страницы: 52

Бренд: Samson Страницы: 78

Бренд: Rachio Страницы: 16

Бренд: Rain Bird Страницы: 48

EtherNetIP ControlPlex CPC12EN

Бренд: E-T-A Страницы: 28

Бренд: Fanimation Страницы: 2

Бренд: M2M Страницы: 24

Pulsafeeder MPC Vector

Бренд: Idex Страницы: 114

Бренд: Lauda Страницы: 40

Бренд: Osaka Страницы: 12

MultiConnect Dragonfly MTQ-MNA1-B01

Бренд: Multitech Страницы: 45

Бренд: Victaulic Страницы: 2

Бренд: FADAL Страницы: 2

Бренд: Eaton Страницы: 2

Бренд: Audioplex Страницы: 1

Бренд: Ravel Страницы: 33

Бренд: L&L KILNS Страницы: 12

Бренд: M-system Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды