background image

40985_F

12-08-11

15

Manufactured under one or more of these patents.  U.S. Patents: 5332944, 5361215, 5550753, 5559720, 5,883,459, 6253227, 6282370, 6590188, 6976052, 6965815, 7030343, 7,417,834 b2,
Canadian Patent: 2342614, Australian patent: 2373248 other patents both foreign and domestic applied for and pending.   All material copyright of Balboa Water Group.

Information 

System Information 

The System Information Menu displays various settings and 
identifi cation of the particular system. As each item in the 
menu is highlighted, the detail for that item is displayed at 
the bottom of the screen. 

Software ID (SSID) 

Displays the software ID number for the System.

System Model  

Displays the Model Number of the System.

Current Setup 

Displays the currently selected Confi guration Setup Number.  

Confi guration Signature 

Displays the checksum for the system confi guration fi le.

Heater Voltage  (Feature not used on CE rated systems.) 

Displays the operating voltage confi gured for the heater. 

Heater Wattage as Confi gured in Software  (CE Systems Only.)

Displays a heater kilowatt rating as programmed into the control system software (1-3 or 3-6). 

Heater Type  

Displays a heater type ID number. 

Dip Switch Settings  

Displays a number that represents the DIP switch positions of S1 on the main circuit board.

Panel Version  

Displays a number of the software in the topside control panel.

System Information

Back

Software ID (SSID)

System Model
Current Setup
Configuration Signature
Heater Voltage
Heater Type

Software ID (SSID):
M100_101 V0.6

Содержание TP800 series























Отзывы: