background image

8  |  Baker Hughes

Copyright 2020 Baker Hughes Company. All rights reserved.

Installation - Alignment

Alignment Warning

This valve must be properly aligned with the piping to prevent 

pipe interference with the disc. After installing the valve, check 

disc rotation as follows:
1.  Disconnect  actuator  from  disc.  To  do  this,  refer  to  point 

8.C. of Installation - Assembly Section to remove clevis pin 

from  the  split  clamp  arm.  Rotate  clamp  arm  to  free  pin  if 

necessary.

2.  Rotate  clamp  arm  slowly  to  prevent  damage  to  the  disc 

sealing edge if interference occurs. If disc can rotate through 

90°arc, alignment is correct.

3.  Realign valve with pipe if there is interference. 
4.  Reassemble.
If heavy wall piping or thin wall piping or tubing is used, see other 

instructions from this Installation - Alignment section.

Standard Commercial Wrought Steel 

Pipe 

Use only flat face or raised face flanges. If using iron flanges, limit 

bolting torque to prevent fracture of the flange which is not fully 

supported by the MiniTork body. Use only carbon steel (ASTM 

A307 GrB or equivalent) bolting with iron flanges.

Weld Neck Flanges

Flange bore should be Schedule 40.
Gaskets are required for unlined valves only. 
Gasket Inside Diameter (I.D.) should be equal to pipe Outside 

Diameter (O.D.).

Figure 3

Содержание Masoneilan MiniTork II 37002 Series

































Отзывы: