background image

4 | Baker Hughes 

© 2021 Baker Hughes Company. All rights reserved. 

 

 
 

 

WARNING 

 
BEFORE  installing,  using  or  carrying  out  any  maintenance  tasks  associated  with  this  instrument, 
READ THE INSTRUCTIONS CAREFULLY. 
 
These instruments have been designed, manufactured and tested in accordance with the essential 
safety requirements of the Ukranian standard for explosible atmospheres ACTY 7113, ACTY 7114 
& GOST 22782.5-78. 
 
 

Products  certified  as  flameproof  equipment  or  for  use  in  intrinsically  safe  installations 
MUST BE: 

 
a) Installed, put into service, used and maintained in compliance with national and local regulations 

and  in  accordance  with  the  recommendations  contained  in  the  relevant  standards  concerning 
potentially explosive atmospheres. 

b) Used only in situations that comply with the certification conditions shown in this document and 

after verification of their compatibility with the zone of intended use and the permitted maximum 
ambient temperature. 

c)  Installed,  put  into  service  and  maintained  by  qualified  and  competent  professionals  who  have 

undergone  suitable  training  for  instrumentation  used  in  areas  with  potentially  explosive 
atmospheres.

 Such trainings are not supported by Baker Hughes.

 

It is the end user's responsibility to: 

•  Verify material compatibility with the application 

•  Ensure  proper  use  of  fall  protection  when  working  at  heights,  per  Safe  Site  Work 

Practices 

•  Ensure use of proper Personal Protective Equipment 

•  Take  the  appropriate  actions  to  ensure  that  site  personnel  who  are  performing 

installation,  commissioning  and  maintenance  have  been  trained  in  proper  site 
procedures for working with and around equipment, per Safe Site Work Practices 

Baker  Hughes  reserves  the  right  to  discontinue  manufacture  of  any  product  or  change 
product materials, design, or specifications without 

notice. 

 
Under certain operating conditions, the use of damaged instruments could cause a degradation of 
the performances of the system which may lead to personal injury or death.  
 
Use only 

Baker Hughes Masoneilan

 replacement parts, which are provided by the manufacturer, to 

guarantee that the products comply with the essential safety requirements of the Ukranian standard 
mentioned above. 
 

 

 

 

Содержание Masoneilan 7700E
















Отзывы: