background image

14  |  

Baker Hughes

© 2023 Baker Hughes Company. All rights reserved.

 b

.    Packing Manual Ref 34620 is also available as 

an additional aid while completing the packing 

installation.

 c

.   The packing should be checked for leakage.

 

  

 Note:

 

All exposed surfaces of the packing set must 

be covered with the lubricant.

 d

.    Packing load should be checked after the valve has 

cycled approximately 500 times.  Adjust if necessary.  

Plant maintenance / operation personnel should 

periodically inspect valves to spot leakage.  Adjust if 

necessary and per OEM recommendations.  If leak 

is not resolved, packing and any non-confirming 

hardware part must be replaced.

5.1.4 Packing Box Efficiency

The constant supervision of the packing box is one of the 

main routing operations of the maintenance service. In order 

to provide a correct functioning of the valve, the packing 

should not be tightened over the compression value sufficient 

to provide the tightness. The packing box efficiency is 

obtained by the compression of the packing, or by combining 

it with use of the lubricant. As it wears, gradually re-tighten the 

packing up to the limits of the possible compression. In order 

to add packing, it is necessary only to remove the packing 

follower and flange and introduce one or two split rings.

Note: In case of urgency, the braided packing of suitable 

section can be inserted without removal of the worn 

rings. Before this operation, the valve must be put out 

of service. If the packing is made up of non-split rings, it 

may be necessary to disassemble the valve, remove the 

worn packing, and follow directions to reassemble.

5.2   Repair of Parts

Before re-assembly, the parts must be carefully examined in 

order to eliminate any scratched, worn or damaged parts.

5.2.1   Guiding Surfaces

The guiding surfaces of the cage and valve plug, the guide 

bushing, and the guiding surfaces of the plug stem and 

auxiliary pilot plug must be checked in particular. If there is 

only slight damage, a light abrasive can be used.
Otherwise the part must be replaced as soon as possible 

(see paragraph “Spare parts”).

Cage

Pilot

Guiding 

surface

Guiding

surface

Seating

surface

Figure 2 - Cage and Valve Plug

5.2.2   Seating Surfaces

Valve Plug

Seat Ring

Plug seating

surface

Pilot seating

surface

(41405 only)

Guiding 

surface

Guiding surface

Seating surface

Seating surface

Seat ring seating surface

31°30'

32°30'

62°30'

57°30'

29°30'

30°30'

Figure 3 - Seating Surfaces

Inspect all seating surfaces per Figure 3 which represents all 

plug and seat types.
For type 41405 valves, if the surface of the auxiliary pilot 

plug (20) is damaged, the auxiliary pilot plug must be 

replaced (see paragraph “Spare parts”).

Содержание Masoneilan 41005 Series





















































Отзывы: