background image

Masoneilan 31000 Series Control Valve Instruction Manual  |  6

Copyright 2020 Baker Hughes Company. All rights reserved.

NOTE: Carefully place the valve lever (135) on to the 

splines so that its free end reaches as near as possible 

(this depending on the splines of the plug shaft) to the 

housing wall of the yoke (Figure 6 distance approxi-

mately 28 mm). The position of the plug (3) should not 

be allowed to change during this process.

3.     Secure  the  yoke  to  the  valve  body  with  screws  (19)  

(Figure 1).

7.3  Setting the Actuator  

(Figures 6, 7, 8) 

The actuator setting depends on the required fail-safe position of 

the valve (see Step 1).
Since the seat and plug are of soft materials, the lever (135) must 

be  set  so  that  the  valve  produces  the  required  tightness. The 

handwheel or adjusting tool (Figure 6), can be used as an aid.
The selected tool is screwed until the plug is brought into the 

closed  position.  The  tightness  of  the  seat/plug  seal  can  be 

checked  using  an  appropriate  method  with  the  handwheel  or 

adjusting  tool  being  tightened  until  the  required  tightness  is 

obtained.

It is essential that the instructions for setting the ac-

tuator be carefully followed. An incorrect setting will 

lead to wear of seat or plug.

Figure 4

Section View of the Safety Packing

1.   Actuator Settings
A.   Valve closed on air failure (Air to open) (Figure 7)

 

a.     Determine the position of the lever at which the valve 

reaches  the  required  tightness  and  measure  the  “D” 

distance from the contact surface of the spring barrel 

on the yoke to the beginning of the hole for the clevis 

pin in the lever (135).

 

b.     The  clevis  (100)  can  now  be  adjusted  so  that  the 

distance from the beginning of the hole for the clevis 

pin to the contact surface for the yoke is 1 to 2 mm less 

than the previously measured “D” distance.

 

c.     Remove the handwheel or setting tool and secure the 

spring barrel with the screws (101) and washers (102).

Figure 2

Figure 3

Fitting Tool 

for Seat 

Ring/Valve 

Size

Part Number

1” (25mm) 

2” (50mm) 

3” (80mm)

603003910-779-0000 

603003940-779-0000 

603003950-779-0000

Assembly Tool for 

Packing Box

Assembly Tool for 

Seat Rings

Ref. Order No. for the 

Set: 00-603004100-799

Packing 

Tool Kit

Part Number

Tools/Kit 

for Packing 

Assembly

603004100-888-

0000

1. Reference CES 495 for details; 

  Pages 11-12

2. Above parts available via iSTORE

Содержание Masoneilan 31000 Series

















Отзывы: