background image

 

 

22. Keep 

all

 cords dry, free from grease and oil, and protected from sparks and hot metal.

 

23. Inspect power and control cables periodically. Replace if damaged or bare wires are 

exposed. 

Bare wiring can kill! DO NOT 

touch live electrical components or parts.

 

24. 

DO NOT

 bypass or defeat any safety interlock systems. 

 

TECHNICAL SPECIFICATIONS 

 

Capacity 

30T 

Capacity Mild Steel 

8ga. [0.1644”] (4.17mm) 

Capacity Stainless Steel 

10ga. [0.1345”] (3.41mm) 

Stroke 

5.9” (150mm) 

Back Gauge 

4.1” – 21.6” (105 – 550mm) 

Bending Width 

48” (1220mm) 

Bending Thickness 

0.157” (4mm) 

Distance Between Columns 

51.9” (1320mm) 

Bottom Die V’s 

4@ 0.75”, 1”, 1.5”, and 2” (19.05, 25.4, 38.1, and 50.8mm) 

Bottom Die Hardness 

50 HRC 

Motor Power 

4hp (3.0kW), 220V, 3ph, 60hz, 6.8A 

Hydraulic Oil 

1 gal. (3.78L) 

Machine Size 

78.3” x 31.5” x 49.2” (1990 x 800 x 1250mm) 

Packing Size 

85.4” x 36.2” x 56.3” (2170 x 920 x 1430mm) 

N.W./G.W. 

1147/1367lbs (520/620kg) 

Based on a material tensile strength of *60000 PSI 

– mild steel 

**100000 PSI 

– stainless steel 

 

TECHNICAL SUPPORT 

Our technical support department can be reached at 920.684.4990 and asking for the support 
desk for purchased machines. Tech Support handles questions on machine setup, schematics, 
warranty issues, and individual parts needs: (other than die sets and blades). 
For specific application needs or future machine purchases contact the Sales Department at: 
[email protected]Phone: 920.684.4990, or Fax: 920.684.3944. 

 

Note: The photos and illustrations used in this manual are representative only and 

may not depict the actual color, labeling or accessories and may be intended to illustrate 
technique only.

 

 

Note: The specifications and dimensions presented here are subject to change 

without prior notice due to improvements of our products. 

 

Содержание BP-4830





































Отзывы: