background image

 

 

CALIFORNIA PROPOSITION 65 

 

WARNING: Cancer and Reproductive Harm. 
www.P65Warnings.ca.gov 

 
 

SAFETY PRECAUTIONS 

 

Metal working can be dangerous if safe and proper operating procedures are not followed. As 
with all machinery, there are certain hazards involved with the operation of the product. Using 
the machine with respect and caution will considerably lessen the possibility of personal injury. 
However, if normal safety precautions are overlooked or ignored, personal injury to the operator 
may result. 
Safety equipment such as guards, hold-downs, safety glasses, dust masks and hearing 
protection can reduce your potential for injury. But even the best guard will not make up for poor 
judgment, carelessness or inattention. 

Always use common sense 

and exercise 

caution

 in 

the workshop. If a procedure feels dangerous, don’t try it. 

REMEMBER:

 

Your personal safety is your responsibility

 

 

 

Dear Valued Customer: 

•  All Baileigh machines should be used only for their intended use. 
•  Baileigh does not recommend or endorse making any modifications or alterations to a 

Baileigh machine. Modifications or alterations to a machine may pose a substantial risk of 
injury to the operator or others and may do substantial damage to the machine. 

•  Any modifications or alterations to a Baileigh machine will invalidate the machine’s warranty. 

 

P

LEASE ENJOY YOUR 

B

AILEIGH MACHINE

!

 

....P

LEASE ENJOY IT 

SAFELY! 

 
1. 

FOR YOUR OWN SAFETY, READ INSTRUCTION MANUAL BEFORE OPERATING THE

 

MACHINE.

 Lea

rn the machine’s application and limitations as well as the specific hazards. 

2. 

Only trained and qualified personnel can operate this machine. 

3. 

Make sure guards are in place and in proper working order before operating 
machinery. 

WARNING:

 FAILURE TO FOLLOW THESE RULES MAY RESULT IN 

SERIOUS PERSONAL INJURY 

Содержание BP-4830





































Отзывы: