Baelz Automatic 373-E07 Скачать руководство пользователя

Страница: 29 / 36

BA_373-E07_04_DEF_MJ_1821

29 |

W. Baelz & Sohn GmbH & Co.

· Koepffstrasse 5 · 74076 Heilbronn · Germany ·

www.baelz.de Seite | Page

Motorized Linear Actuator

baelz 373-E07

7.6 Errors

7.6.1 Errors after an initialization run

Following a successful initialization run, only the green LED is lit.

If the red LED is flashing, this indicates an error following an unsuccessful initialization run.

The first error to occur during initialization is shown. If the green LED is lit, the unit had already

been initialized before the current initialization run. If the green LED is flashing, the unit had not

been successfully initialized previously.

The red LED shows errors occuring during initialization as follows:

Error code 1: interval interval etc.

Error code 2: interval interval etc.

etc. up to ...

Error code 8: interval interval

etc..

Following an initialization run, the red LED shows only initialization errors as long as DIP switch

12 is set to 1. This enables a clear differentiation between errors occuring during initialization

and those occuring during normal positioner operation. Setting DIP switch 12 from 1 back to 0

permits the red LED to show any normal operational errors instead of initialization errors which

may have occured.

Error code

Error

Corrective action

1 →

1 x

Invalid status of initialization run. Possible

cause: EMI (electromagnetic interference).

Remove source of interference.

2 →

2 x

Sensor malfunction at analogue input AI1:

No signal from potentiometer.

Check connection terminals 91, 92, 93

(see wiring diagram, Fig. 24, page 22).

Replace potentiometer if necessary.

3 →

3 x

Potentiometer value at AI1 too small.

Possible cause: EMI.

Remove source of interference.

Replace potentiometer if necessary.

4 →

4 x

Potentiometer value at AI1 too large.

Possible cause: EMI.

Remove source of interference.

Replace potentiometer if necessary.

5 →

5 x

Wrong direction of travel

Check motor (97, 98, 99) and potentiometer

(91, 92, 93) connections (see wiring diagram,

Fig. 24, page 22).

Remove source of interference.

6 →

6 x

Obstruction: potentiometer or motor not moving.

Check connections, set N↔S switch to "N",

remove any obstructions.

7 →

7 x

Stroke too long.

Fit actuator to a valve with nominal stroke

length < 22 mm.

8 →

8 x

Stroke too short.

Fit actuator to a valve with nominal stroke

length > 8,7 mm, remove any obstructions.

Содержание 373-E07





































Результаты поиска

Содержание 373-E07

Отзывы:

Похожие инструкции для 373-E07

Бренды по названию

Популярные бренды

Baelz Automatic 373-E07, Руководство по эксплуатации

Результаты поиска

Содержание 373-E07

Отзывы:

Похожие инструкции для 373-E07

Бренды по названию

Популярные бренды