Bad Boy 4025H 2021 Скачать руководство пользователя

Страница: 117 / 128

BAD BOY TRACTOR

Symptom

Inspection item

Action

1. The implement does not be lifted.



Is the hydraulic flow control dial in the close

position?



Adjust the hydraulic flow control dial.



Is the transmission oil level low?



Refill the transmission oil.



Is the air taken in the fluid suction system?



Tighten the filter or connection parts. Re

place the pipe or O-ring if damaged.



Is the oil filter clogged?



Clean or replace it.



Is the Selective control valve lever in the de-

tent position?



Put the Selective control valve lever in

the neutral position.



Is the hydraulic pump defective?



Contact the dealer for repair.



Is the cylinder damaged?



Contact the dealer for repair.

2. The implement does not be low-

ered.



Is the hydraulic flow control dial in the close

position?



Adjust the hydraulic flow control dial.



Is the position control lever on the lowest po-

sition?



Move the position control lever.



The implement cannot be lowered even

though the position control lever is placed in

the lowest position.



Contact the dealer for repair.

TROUBLESHOOTING - HYDRAULIC SYSTEM

4025h_4035h.indb 6

2020-09-18 오후 6:23:24

Содержание 4025H 2021

































































































































Результаты поиска

Содержание 4025H 2021

Отзывы:

Похожие инструкции для 4025H 2021

Бренды по названию

Популярные бренды

Bad Boy 4025H 2021, Руководство оператора

Результаты поиска

Содержание 4025H 2021

Отзывы:

Похожие инструкции для 4025H 2021

Бренды по названию

Популярные бренды