Bad Boy 4025H 2021 Скачать руководство пользователя

Страница: 100 / 128

MAINTENANCE

ROUTINE MAINTENANCE

OPENING HOOD

1. The hood can be unlocked by pull-

ing the opening knob.

2. Slightly lift the hood with both

hands and the hood is automati-

cally lifted by the gas spring.

3. To close the hood, press its front

down slightly until a "click" sound

is heard.

4. After closing the hood, lift it to

check that the hood is securely

fixed.

CHECKING AND REPLACING ENGINE OIL

CHECKING

Pull out the oil dipstick, clean it, and

then insert it into its original position.

Then, pull it out again and check if

the oil level is within the specified

range. If the oil level is too low, add

new oil so that the level is within the

allowable range.

To drain oil, remove the drain plug on

the bottom of the engine. Fill new en-

gine oil through the filler after install

ing the drain plug. Change engine oil

periodically with proper engine oil ac-

cording to the temperature and oper-

ating condition.

(1) Opening knob

(1) Oil dipstick

(2) Oil inlet

REPLACING

(1) Drain plug

•

First 50HR engine oil has to be

changed.

NOTE

111

222

4025h_4035h.indb 5

2020-09-18 오후 6:23:22

Содержание 4025H 2021

































































































































Результаты поиска

Содержание 4025H 2021

Отзывы:

Похожие инструкции для 4025H 2021

Бренды по названию

Популярные бренды

Bad Boy 4025H 2021, Руководство оператора

Результаты поиска

Содержание 4025H 2021

Отзывы:

Похожие инструкции для 4025H 2021

Бренды по названию

Популярные бренды