background image

29

Secure bottom of front panel 

to fl oor with 2" nails spaced 6" apart. 

Angle nails into fl oor frame 

(Fig. C)

.

Trim

Fig. B

 2" 

(5,1 cm)

 

Nail

2

3

1

BEGIN

FRONT WALL INSTALLATION

Install front wall on fl oor between side walls.

Secure lower and upper corner of side 

wall panel to front wall trim with 

(2) 2" nails

 (Fig. A, Fig. B)

.

Secure side wall panel to front wall trim 

with 2" nails spaced 6" apart 

(Fig. B)

.

Secure front wall bottom plates to fl oor 

frame with 3" nails.

Secure the front

 wall trim to fl oor with (1) 

3" screw at each side. 

Angle screws into fl oor frame 

(Fig. D)

.

Secure the front wall trim to side wall top 

plate with (1) 3" screw at each side 

(Fig. E)

.

3" (7,6 cm)

x4

2" (5,1 cm)

x40

Trim

Fig. B

2"

(5,1 cm)

Nail

Panel

3" (7,6 cm) 

Nails

 Angle nails

 into fl oor frame.

2" (5,1 cm)

Nail

Fig. C

3" (7,6 cm) 

Screw

Top Plate

Fig. E

3" (7,6 cm) 

Screw

Trim

Fig. D

PARTS REQUIRED:

3" (7,6 cm)

x6

You have fi nished standing your walls.

Remove the temporary brace.

Repeat steps to secure the other 

side of front wall.

FINISH

Secure panels to bottom of trim fi rst.

ENSURE PANEL CORNERS ARE FLUSH.

2" 

(5,1 cm)

 

Nails

2" 

(5,1 cm)

 

Nails

6" 

(15,2 cm)

6"

(15,2 cm)

Flush

Содержание Handy Home Products KENNESAW
























































Отзывы: