Baby Lock Quest PLUS BLQ2-PL страница 65 Скачать руководство пользователя

Страница: 65 / 104

5. Pass the upper thread down through the hole

in the presser foot. Pull down the buttonhole

lever and position it behind the bracket on the

buttonhole foot. Gently hold the end of the

upper thread in your left hand, and then start

sewing.

Note:

When you start to sew darning

pattern before the buttonhole lever is

lowered, LCD screen will show the

animated warning message to remind you

to lower the buttonhole lever.

7. If the tear is too large to cover with one darning

pattern, reposition the fabric and sew additional

darning patterns for better coverage.

6. Darning stitches are sewn from the front of

the presser foot to the back, as shown.

The evenness of darning

may vary depend

ing on the sewing condition

type of fabrics

You can correct the unevenness of darning

- Press the " " button.

A. If the left corner is lower than the right side,

press the stitch length adjusting button "+".

B. If the right corner is lower than the left side,

press the stitch length adjusting button "".

adjusting

adjusted.

stitch

, i.e.

stitch

- Press the "

" button again after

return to the normal LCD screen.

Note:

Only Group 2-B patterns 46-48 can

To adjust the evenness of darning stitch

Содержание Quest PLUS BLQ2-PL









































































































Результаты поиска

Содержание Quest PLUS BLQ2-PL

Отзывы:

Похожие инструкции для Quest PLUS BLQ2-PL

Бренды по названию

Популярные бренды

Baby Lock Quest PLUS BLQ2-PL, Инструкция и справочник

Результаты поиска

Содержание Quest PLUS BLQ2-PL

Отзывы:

Похожие инструкции для Quest PLUS BLQ2-PL

Бренды по названию

Популярные бренды