Baby Lock Quest PLUS BLQ2-PL страница 2 Скачать руководство пользователя | Manualshive

Страница: 2 / 104

background image

SAFETY INSTRUCTIONS

When using an electrical appliance, basic safety should always be followed, including the

following:
Read all instructions before using this sewing machine.

-To reduce the risk of electrical shock:

1. An appliance should never be left unattended when plugged in.
2. Always unplug this appliance from the electrical outlet immediately after using and before

cleaning.

3. Always unplug before checking and re-lamping. Contact the authorized retailer or service

center for repair in the event of failure if the machine is with 200mW, 300mW and 200mW

LED lamp, which is not user-replaceable.

-To reduce the risk of burns, fire, electrical shock, or injury to persons:

1. Do not allow to be used as a toy. Close attention is necessary when this appliance is

used by or near children.

2. Use this appliance only for its intended use as described in this manual. Use only the

attachments recommended by the manufacturer as contained in this manual.

3. Never operate this appliance if it has a damaged cord or plug, if it is not working properly,

if it has been dropped or damaged, or dropped into water. Return the appliance to the

nearest authorized retailer or service center for examination, repair, electrical or

mechanical adjustment.

4. Never operate the appliance with any air openings block. Keep ventilation openings of the

sewing machine and foot control free from accumulation of lint, dust, and loose cloth.

5. Keep fingers away from all moving parts. Special care is required around the sewing

machine needle.

6. Always use the proper needle plate, a wrong needle plate can cause the needle to break.
7. Do not use bent needles.
8. Do not pull or push fabric while stitching. It may deflect the needle causing it to break.
9. Switch the sewing machine off ("O") when making any adjustments in the needle area,

such as threading needle, changing needle, threading bobbin, or changing presser foot,

and the light.

10.Always unplug sewing machine from the electrical outlet when removing covers, lubricating,

or when making any other user servicing adjustments mentioned in the instruction manual.

11.Never drop or insert any object into any opening.
12.Do not use outdoors.
13.Do not operate where aerosol spray products are being used or where oxygen is being

administered.

14.To disconnect, turn all controls to the off ("O") position, then remove plug from outlet.
15.Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
16.The sound pressure level under normal operating conditions is 75dB(A).
17.

DANGER

WARNING

SAVE THESE INSTRUCTIONS

This sewing machine is intended for household use only.

Please turn off the machine or unplug when the machine is not operating properly.

1

«
1
2
3
4
...
»

Содержание Quest PLUS BLQ2-PL









































































































Отзывы:

Нет отзывов

Похожие инструкции для Quest PLUS BLQ2-PL

Бренд: Fastbind Страницы: 4

Бренд: UnionSpecial Страницы: 40

Бренд: Janome Страницы: 68

Бренд: Unicorn Страницы: 43

Бренд: Fortis Страницы: 12

Бренд: Mytee Страницы: 12

Бренд: Janome Страницы: 8

Бренд: Bernette Страницы: 72

Бренд: Quilt EZ Страницы: 47

Smoke 700 Magic

Бренд: Audibax Страницы: 2

Бренд: Radio Shack Страницы: 24

PROGRESSION 600ES-LED

Бренд: Gamma Страницы: 16

Бренд: Gear4music Страницы: 16

Бренд: JUKI Страницы: 59

Бренд: SCANMASKIN Страницы: 62

Бренд: JUKI Страницы: 56

Бренд: Panasonic Страницы: 112

Бренд: Panasonic Страницы: 144

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды