manualshive.com logo in svg

Baby Lock Ellisimo BLSO, Руководство по обслуживанию

Поделиться
Скачать
Baby Lock Ellisimo BLSO Скачать руководство пользователя страница 44

4 - 23

Adjustment

In

spection and 

Adjustment

Front/back and left/right position of feed dog

[Adjustment standard]

The clearance (front/back) between the forward edge of the feed dog middle tooth and needle plate A is to 3.2 to
3.8mm, and the clearance (left/right) between the feed dog and needle plate A must be equal.

[Adjustment procedure]

1. Remove the needle plate B, the presser foot and the needle.
2. Start the test mode, and then select the “06” (Feed dog position mode).

3. Press the 

 button. (the feed dog comes to center)

4. Remove the 2 flat screws (M4) of the needle plate A, and then remove the needle plate A.
5. Loose the 2 bind screws (M3x8) of the feed dog, temporarily attach the needle plate A, and adjust the front/back

and left/right position of the feed dog.

*Key point

• Adjust the clearance (front/back) between the forward edge of the feed dog middle tooth and the needle plate 

A is to 3.2 to 3.8mm.

• Adjust the clearance (left/right) between the feed dog and the needle plate A must be equal.
• Do not assemble feed dog to diagonally to the needle plate A.

6. Secure the feed dog with the 2 bind screws (M3x8). (tightening torque: 0.78 to 1.18N· m)
7. Fully tighten the 2 flat screws (M4) of the needle plate A.

3.2-3.8mm

b

a

a=b

Parallel

Bind screw (M3x8)

Bind screw (M3x8)

46

Содержание Ellisimo BLSO


































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды