BAB TECHNOLOGIE APPMODULE IP Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 62

BAB TECHNOLOGIE APPMODULE IP Скачать руководство пользователя страница 48

APP

MODULE Documentation

48 BAB TECHNOLOGIE GmbH

7.2

AUTOMATIC SMART HOME APP UPDATE

As of firmware 1.4.0, you no longer need to check the BAB APPMARKET for updates for installed apps. In

the App Manager you can set if you want to search for updates automatically or if you want to trigger

the search manually.

Open the App Manager and click on the button with the gear symbol.

Activate the automatic Smart Home App updates here. If the automatic app updates is deactivated,

click on the Check for updates button to start a manual search.

If the automatic app update is activated, you can optionally use the Indicator Address (EIS 1) to display

in a visualization, for example, that an app update is present (if a 0 is sent to the group address, no

update is present, if a 1 is sent, one or more updates are present).

Figure 46: Update Configuration

If the Automatic App Update is activated, the

APP

MODULE checks for updates once a day. The time of

the search depends on the last boot process of the

APP

MODULE and is determined automatically. The

time cannot be set. If the automatic search is activated, the

APP

MODULE searches for updates directly

after activation.

If an update is available for an installed Smart Home App, this is displayed in the App Manager.

Figure 47: Smart Home App Update available

Click on the button "Update available". A window opens with the "ChangeLogs" of the APP.

All changes between the currently installed Smart Home App version and the App version provided for

the update are displayed

«
...
46
47
48
49
50
...
»

Содержание APPMODULE IP































































Отзывы:

Нет отзывов