BAB TECHNOLOGIE APPMODULE IP Скачать руководство пользователя страница 17

Страница: 17 / 62

APP

MODULE Documentation

BAB TECHNOLOGIE GmbH 17

ADJUSTING THE NETWORK SETTINGS OF THE APPMODULE

If the network prerequisites have been created, you can now access the configuration of the

APP

MODULE in order to adjust the network settings to the local requirements there. To do this, please

proceed as described below:



Enter the IP address of the

APP

MODULE in the address line of your browser (for factory settings:

192.168.1.229).

Figure 12: APPMODULE Webinterface



The start page of the

APP

MODULE opens up. Click "Log In".



A login dialog appears. For factory settings, the login data is as follows:

Username:

admin

Password:

admin

Figure 13: Login dialog

Note: The password must be changed immediately when logging in for the first time. If the password is

lost, the device cannot be reset!

Note: Logging in only works if the browser is authorised to save cookies!



The view on the start page changes. You can now access the following levels:



App Manager



Configuration



Information



Log Out

Содержание APPMODULE IP































































Результаты поиска

Содержание APPMODULE IP

Отзывы:

BAB TECHNOLOGIE APPMODULE IP, Документация, Страница: 17 / 62

Результаты поиска

Содержание APPMODULE IP

Отзывы: