BAB TECHNOLOGIE APPMODULE IP Скачать руководство пользователя страница 26

Страница: 26 / 62

APP

MODULE Documentation

26 BAB TECHNOLOGIE GmbH

4.1.1

KNX CONFIGURATION

The KNX-specific settings of the

APP

MODULE are made in the “KNX” menu. The KNX settings are

available both for a

APP

MODULE KNX (10495) and for the

APP

MODULE EnOcean (13501) &

APP

MODULE IP (10491). For the

APP

MODULE EnOcean &

APP

MODULE IP, the settings are used to

configure the KNXnet/IP server.

Physical address:

Here, you can determine the physical address to be used by the

APP

MODULE in the KNX network. Please make sure that the

physical address corresponds to the installation site and does

not occur twice.

KNXnet/IP Routing:

Activates KNXnet/IP Routing for coupling lines and areas via IP.

Can only be activated if the physical address corresponds to

that of a line or area coupler. KNXnet/IP Routing is based on

multicast and all devices send to a multicast group

224.0.23.12. Since multicast packages are usually not

transferred by routers, “routing” only works within a subnet.

KNXnet/IP Tunneling:

Activates KNXnet/IP Tunneling access to the device. This

connection can be used to program KNX devices or to

exchange data. The

APP

MODULE is the server. The above

address is used as the physical address for the connection. For

each address, only one connection can be established at any

one time. On the TCP/IP layer, the connection is made by

means of unicast to UDP port 3671.

KNXnet/IP Tunneling Addresses:

After activating the KNXnet / IP tunneling, the input field for

the tunneling addresses is displayed. This address is used by the

internal KNXnet / IP server for a KNXnet / IP tunneling

connection established to the device (use of the

APP

MODULE

as programming interface). Please note that this address must

not be the same as the physical address (see above) and that it

is not used by any other device in the line.

Note: These addresses are used to establish a connection with

the ETS commissioning software to use the

APP

MODULE as an

interface to KNX. Since ETS 5, at least 2 free addresses are

required here.



Click “Save configuration” to apply the settings.

Note: The KNXnet/IP app for EnOcean is available in the APP MARKET for the

APP

MODULE EnOcean

(13501).

Содержание APPMODULE IP































































Результаты поиска

Содержание APPMODULE IP

Отзывы:

BAB TECHNOLOGIE APPMODULE IP, Документация, Страница: 26 / 62

Результаты поиска

Содержание APPMODULE IP

Отзывы: