background image

Service Program

3

Infusomat® fmS 2.3 gb  

3 -  7

 

The activation of the "10 minutes off” alarm is only permissible, if:

-

the staff call is connected and

-

the Infusomat® fmS has an attention label (label drawing no. 

M007100000F04).

1.

OK activates the function.

2.

Select alarm tone with NEXT.

3.

Acknowledge with YES.

4.

Return to initial function with END.

Staff Call

Function 430.0

Different staff call modes can be selected:

-

Dynamic with OFF Alarm

-

Dynamic without OFF Alarm

-

Static without OFF Alarm

For further details see staff call line in the instructions for use.

An additional switch-on pulse (YES/NO) can be activated for each 

mode to test the staff call unit.

1.

OK activates the function.

2.

Select staff call type with NEXT.

3.

Acknowledge with YES.

4.

Return to initial function with END.

Special Functions

Function 440.0

Special functions can be activated in the Service Program, which 

are then available on the user interface. Deactivated special func-

tions will not be displayed. The SM softkey will not be displayed 

in standard operation, if all special functions are deactivated. - 

Special functions to be selected, see 

Fig.: 1 - 2

.

1.

OK activates the function.

2.

Select special functions with NEXT.

3.

Activate / deactivate the respective function with YES/NO.

4.

Return to main menu with END.

Fig.: 3 - 6   

Содержание Infusomat fmS























































































Отзывы: