Azbil ACTIVAL FC200 Скачать руководство пользователя

Страница: 16 / 20

AB-6675

IMPORTANT:



While the terminal cover is removed, do not touch the terminal block or allow anything to touch the terminal

block.



If the service pin switch is kept pressed for longer than 5 seconds, the mode will be switched and operation

error (data point trouble) will be occurred. In such a case, press the service pin switch again and keep it
pressed for longer than 10 seconds to go back to the normal mode.

Table 1. Basic address setting of this product and other Intelligent Component Series devices

Add. Device

Sub-DO

Sub-DI

Outdoor air damper

Exhaust air damper

3 Return

air

damper

Switch damper of total heat exchanger for outdoor air

Switch damper of total heat exchanger for exhaust air

Chilled/hot water valve / Chilled water valve

Filter alarm

Hot water valve (Chilled water valve*)

Humidifying ON/OFF

8 Humidifying

valve

D (13) Reserved

E (14) Reserved

F (15) Reserved

Notes:



1. For ‘chilled/hot water valve + chilled water valve’ application, set address 6 for chilled/hot water valve and 7 for chilled water valve.



2 Items in bold characters are the basic address to set for this product.



3 The above table is a basic setting example. Set address and use sub-I/O in response to system configuration, installation location, and

wiring best suitable for your application.

Содержание ACTIVAL FC200





















Результаты поиска

Содержание ACTIVAL FC200

Отзывы:

Похожие инструкции для ACTIVAL FC200

Бренды по названию

Популярные бренды

Azbil ACTIVAL FC200, Спецификации и инструкции

Результаты поиска

Содержание ACTIVAL FC200

Отзывы:

Похожие инструкции для ACTIVAL FC200

Бренды по названию

Популярные бренды