background image

AB-6675 

 

Specifications/Instructions 

© 2010–2020 Azbil Corporation. All Rights Reserved. 

Intelligent Component Series 

ACTIVAL

 

Motorized Three-Way Valve 

with Flanged-End Connection (JIS 10K / FC200) 

 

 

 

General 

ACTIVAL

 Model VY5460F is a series of motorized three- 

way valves with flanged-end connection.  Rotary valve and 
actuator are integrated in a single unit. 

Valve size ranges from DN50 (2”) to DN80 (3”), and valve 
body rating corresponds to JIS 10K. 

Actuator has a reversible synchronous motor, which 
operates at a low voltage of 24 V AC. 

Model VY5460F communicates with a controller via SAnet 
(Azbil Corporation’s communication protocol). 

 

 Note 

JIS: Japanese Industrial Standards 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Features 

 

Compact and lightweight: 
Rotary valve actualizes small body and light weight. 

 

Valve and actuator integrated in a single unit: 

 SAnet 

communication: 

Intelligent Component Series ACTIVAL communicates 
with a controller via SAnet, and thus position control 
signal/ position feedback signal is input/output from/to 
the controller. 

 

 

 

Durable actuator with low power consumption. 

 

Linear flow characteristic. 

 

Sub-DI and sub-DO for wire saving: 
Sub-DIO (digital input and output) provided takes signals, 
including humidifying output and differential pressure 
switch of neighboring devices, leading to wire saving. 

 

 

Содержание ACTIVAL FC200





















Отзывы: