Axxess AXDSPL-CH3 страница 5 Скачать руководство пользователя

Страница: 5 / 16

REV. 11/2/2020 INSTAXDSPL-CH3

BLUETOOTH STREAMING INTERFACE

16-pin Header

AX-DSPL-BT

AX-DSPL-SP

AX-DSPL-BT

AX-DSPL-SP

• The

AXDSPL-BT

Bluetooth streaming interface can be used to stream media directly to

the interface.

• While streaming media the volume on the phone will be used. As an option, the

AXBK-1

(sold separately) can be used to control the volume.

Note:

The bass knob included with the

AXDSPL-CH3

can be used if it will not be used to

control a subwoofer.

Important!

Unplug the interface from the vehicle.

Remove (4) Phillips screws securing the interface, then remove the top cover, exposing

the circuit board within.

Locate the 16-pin header on the circuit board.

Important!

Referencing how the

AXDSPL-BT

is laid out in the picture, carefully line up

the header pins to the interface. Gently press down to secure.

Note:

Both interfaces may be damaged if installed wrong.

Reinstall the top cover to complete the installation.

AXBK-1 Installation:
6.

Connect the

Brown

wire from the interface to the

Orange

wire from the

AXBK-1

Ground the

Black

wire from the

AXBK-1

Continued on the next page

Содержание AXDSPL-CH3

















Результаты поиска

Содержание AXDSPL-CH3

Отзывы:

Похожие инструкции для AXDSPL-CH3

Бренды по названию

Популярные бренды

Axxess AXDSPL-CH3, Руководство по установке

Результаты поиска

Содержание AXDSPL-CH3

Отзывы:

Похожие инструкции для AXDSPL-CH3

Бренды по названию

Популярные бренды