Axxess AXDSPL-CH3 Скачать руководство пользователя

Страница: 16 / 16

NOWLEDGE IS

OWER

nhance your installation and fabrication skills by

enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.

Metra recommends MECP
certified technicians

AxxessInterfaces.com

REV. 11/2/20 INSTAXDSPL-CH3

I N S T A L L A T I O N I N S T R U C T I O N S

AXDSPL-CH3

Having difficulties? We’re here to help.

Contact our Tech Support line at:

386-257-1187

Or via email at:

[email protected]

Tech Support Hours (Eastern Standard Time)

Monday - Friday: 9:00 AM - 7:00 PM
Saturday: 10:00 AM - 7:00 PM
Sunday: 10:00 AM - 4:00 PM

SPECIFICATIONS

Input Impedance

1M Ohm

Input Channels

Input Options

High Level or Low Level

Input Type

Differential balanced

Input Voltage

0 - 28-volts (peak-to-peak)

(high level range)
Input Voltage

0 - 4.9-volts

(peak-to-peak)

(low level range)
Ouput Channels

Output Voltage

Up to 5-volts RMS

Output Impedance

50 Ohms

Equalizer Type

15 Band Graphic EQ, +/- 10dB

THD

<0.03%

Frequency Response

20Hz - 20kHz

Crossover Filter

Low pass, band pass, high pass

Crossover Frequency

Selectable 20hz to 20khz

Crossover Slope

12db/24db/36db/48db

Crossover Type

Linkwitz-Riley

Sampling

48kHz

S/N Ratio

105dB @ 5-volts RMS

Operating Voltage

10-16 volts DC

Standby Current Draw

7mA

Operation Current Draw

150mA

Adjustments/Controls

Application via Bluetooth

Remote Output

12 volts DC (signal sense

or with ignition

Содержание AXDSPL-CH3

















Результаты поиска

Содержание AXDSPL-CH3

Отзывы:

Похожие инструкции для AXDSPL-CH3

Бренды по названию

Популярные бренды

Axxess AXDSPL-CH3, Руководство по установке

Результаты поиска

Содержание AXDSPL-CH3

Отзывы:

Похожие инструкции для AXDSPL-CH3

Бренды по названию

Популярные бренды