Axxess AXDSPL-CH3 Скачать руководство пользователя

Страница: 4 / 16

ADDING A FULL-RANGE AMP & SUB TO A FACTORY SYSTEM

Factory Radio

Factory Radio Harness

Interface

Any remaining wires

tape off and disregard

Vehicle T-Harness

Bass Knob

Blue/White

- Amp Turn-On Wire

Cut the male

connector off and

connect speaker

wires to amp

(non-amplified

models only)

White

/ Front Left +

White/Black

/ Front Left -

Gray

/ Front Right +

Gray/Black

Front Right -

Green

/ Rear Left +

Green/Black

/ Rear Left -

Purple

/ Rear Right +

Purple/Black

/ Rear Right -

Unplug connector

Any remaining wires

tape off and disregard

Black

- Ground

Orange

- Control

Factory Amp

If equipped, bypass

and remove

RCA Jacks

(sold separately)

An SPDT relay, Metra part number

E-123

, is required if the amp turn-on

current of all amps exceeds 1-amp.

Interface Harness

Содержание AXDSPL-CH3

















Результаты поиска

Содержание AXDSPL-CH3

Отзывы:

Похожие инструкции для AXDSPL-CH3

Бренды по названию

Популярные бренды

Axxess AXDSPL-CH3, Руководство по установке

Результаты поиска

Содержание AXDSPL-CH3

Отзывы:

Похожие инструкции для AXDSPL-CH3

Бренды по названию

Популярные бренды