0 4
EN
A S S E M B L Y (see page 34)
S A F E T Y N O T E S
Gloves should be worn during installation to prevent crushing and cutting injuries.
The product may only be used for bathing, hygienic and body cleaning purposes.
Children as well as adults with physical, mental and⁄or sensoric impairments must
not use this product without proper supervision. Persons under the influence of
alcohol or drugs are prohibited from using this product.
Do not allow the streams of the shower touch sensitive body parts (such as your
eyes). An adequate distance must be kept between the shower and you.
E L E C T R I C A L C O N N E C T I O N
The installation and test work must be performed by an authorized electrician
under consideration of DIN VDE 0100 part 701 ⁄ IEC 60364-7-701.
The current version of the applicable regulations from VDE, local authorities and
utility companies must be observed for electric installation work.
The entire power is supplied via a 240V⁄N⁄PE ⁄50Hz AC connection.
The system must be protected via a leakage current protective device (RCD⁄ FI) with
a measurement difference current of ≤ 30 mA.
The proper function of this fusing⁄protection must be checked at regular intervals.
The ambient temperature must not be higher than 50ºC.
It must be ensured that the product can be disconnected from the mains, e.g. via a
an all-pin switch as per EN 60335-1, sect. 24.3
The transformer must not be installed in protection zones 0, 1 or 2.
T R A N S F O R M E R
The voltage supply from the 12 V DC SELV must only be fed via the included
transformer type 19769610. The transformer must be installed safe from outside
contact outside the zones 0, 1 and 2 in a flush-type box to be provided by the
customer. (see page )
The transformer must be installed inside the wall in a > Ø 60 mm socket. This socket
inside the wall is connected to the overhead shower via an empty conduit EN 20.
(see page 32)
The mains voltage of 100 - 240 V AC 50 - 60 Hz must be supplied via a existing
shutoff device (switch) as well as a ground fault protector (RCD ⁄ FI) with a
measured differential current of ≤ 30 mA.
The transformer type19769610 is only suited for the voltage supply of the product
26032000.
A different or excessive use is considered non-intended. (The user⁄operator bears the
sole risk.) The intended use includes the adherence to the operating instructions and
the observance of the inspection and maintenance guidelines. The manufacturer⁄seller
of this product does not assume any responsibility for injuries or damage that may be
caused by improper installation or non-intended use.
I N S T A L L A T I O N I N S T R U C T I O N S
⁄ The pipes and the fixture must be installed, flushed and tested as per the applicable
standards. (Installation to EN 1717)
⁄ The plumbing codes applicable in the respective countries must be observed.
⁄ During installation of the product by qualified trained personnel, make sure that the
entire fastening surface is even and smooth (no protruding seams or tile offset), that
the finish of the wall is suitable to apply the product and has no weak points.
⁄ Any work may only be carried out in a de-energized state.
⁄ Pull the connecting line to light⁄transformer into the empty conduit by means of a
cable retractor (EN 20).
⁄ Only standardized materials may be used for the installation.
⁄ All components must remain accessible.
T E C H N I C A L D A T A
Operating pressure:
max. 0,6 MPa
Recommended operating pressure:
0,2 - 0,4 MPa
(1 MPa = 10 bar = 147 PSI)
Hot water temperature:
max. 60°C
Recommended hot water temp.:
42°C
Thermal disinfection:
max. 70°C ⁄ 4 min
The product is exclusively designed for drinking water!
T R A N S F O R M E R
Input (IN):
100 - 240 V ⁄ 50 - 60 Hz ⁄ 70 - 170 mA
Output (OUT):
12 V DC ⁄ 1 A
Protection category:
IP X1
Serial number:
26032000 (see typeplate)
Dimensions:
(see page 32)
weight:
81 g
The specifications are identical to the data on the type plate for the light and the
transformer.
C O N N E C T I N G C A B L E B E T W E E N L I G H T ⁄ T R A N S F O R M
Cable length:
7m
Wire cross section:
ca. 0,25 mm²
- Wire color:
Black (GND)
+ Wire color:
Red (12 V DC)
Connection on the transformer:
Clamp connection
Empty conduit for cable:
EN20
If the connecting cable is shortened, it must be fitted with 0.25 mm² wire end plugs
and a contact length of 8 mm.
I L L U M I N A N T C H A N G E
⁄ Any work may only be carried out in a de-energized state. Here, the voltage
supply must be safely separated via the main switch or mains plugs.
⁄ The operator can perform the illuminant change.
⁄ The wall socket must be outside of the protected zones.
⁄ Order number: 98351000
⁄ Illuminant change (see page 41)
⁄ All spare parts must be purchased at Hansgrohe or the sanitary dealer’s.
S Y M B O L D E S C R I P T I O N
Do not use silicone containing acetic acid!
P R O T E C T E D A R E A (see page 32)
transformer
Empty pipe
230 V
12 V
D I M E N S I O N S (see page 32)
F L O W D I A G R A M (see page 33)
S P A R E P A R T S (see page 43)
C L E A N I N G (see page 38)
M A I N T E N A N C E (see page 41)
0, 1, 2
Содержание Nendo 26032 Series
