background image

Network Camera Devices

6

A3090-1.1 en

Maintenance and cleaning

The Axis network camera devices are maintenance free. Please note the following 
when cleaning the housing:

Before cleaning, disconnect the equipment from the power supply.

Clean the housing with a soft, slightly damp (not wet!) cloth. Never use solvents, 
since these could damage the labelling on the front panel and the display.

When cleaning, ensure that no liquid gets into the equipment or connections.

Remaining dangers

The scope of supply and performance of the data acquisition system covers only a 
small area of measurement technology. In addition, equipment planners, installers and 
operators should plan, implement and respond to the safety engineering 
considerations of measurement technology in such a way as to minimize remaining 
dangers. Prevailing regulations must be complied with at all times. There must be 
reference to the remaining dangers connected with measurement technology. After 
making settings and carrying out activities that are password-protected, you must 
make sure that any controls that may be connected remain in safe condition until the 
switching performance of the amplifier system has been tested.
 
In this manual, the following symbols are used to point out remaining dangers:
 

DANGER

Meaning: Maximum danger level
Warns of an imminently dangerous situation in which failure to comply with safety 
requirements will result in death or serious bodily injury.

WARNING

Meaning: Dangerous situation
Warns of a potentially dangerous situation in which failure to comply with safety 
requirements can result in death or serious bodily injury.

CAUTION

Meaning: Potentially dangerous situation
Warns of a potentially dangerous situation in which failure to comply with safety 
requirements could result in death or serious bodily injury.

Meaning: Electrostatic sensitive devices
Devices marked with this symbol can be destroyed by electrostatic discharge. Please 
observe the precautions for handling electrostatic sensitive devices.

Содержание Axis 211

















Отзывы: