Axeon Water Technologies L1-Series Скачать руководство пользователя страница 27

          L1-Series User’s Manual 
          MKTF-258 

27 

9/14

 

REVERSE OSMOSIS SYSTEM WARRANTY 

 

One-Year Limited Warranty 

 

Warranty Terms 

Subject to the terms and conditions set forth hereinafter, AXEON Water Technologies 
(hereafter  “AXEON”)  warrants  to  the  original  purchaser  (hereafter  the  “Customer”) 
that  the  systems  and  products  manufactured  by  AXEON  are  free  from  defects  in 
material  and  in  workmanship  for  twelve  (12)  months  from  the  Warranty 
Commencement Date (as defined below) only when used strictly in accordance with 
the applicable operating instructions and within the range of the operating conditions 
specified by AXEON for each such product. 

This Warranty does not extend to systems, equipment, or components manufactured 
by  others,  nor  to  systems,  equipment,  or  components  manufactured  by  others  and 
distributed by AXEON. This Warranty does not extend to equipment or components 
manufactured by others which have been incorporated into an AXEON product but, if 
allowable,  AXEON  hereby  assigns,  without  warranty,  to  the  Customer  its  interest,  if 
any, under any warranty made by the manufacturer of such equipment or component. 
This Warranty does not cover disposable items such as fuses, o-rings, regeneration 
materials/chemicals,  or  other  such  disposable  items,  which  must  be  replaced 
periodically  under  the  normal  and  foreseeable  operating  conditions  of  the  goods 
warranted hereby. 

Warranty Commencement Date 

The Warranty Commencement Date for each AXEON product shall be the later of the 
date of: (1) receipt by the Customer, or (2) the date of installation at the Customer’s 
premises  provided  that  such  installation  must  occur  within  three  (3)  months  of 
shipment  from  the  AXEON’s  manufacturing  facility  in  Temecula,  California.  In  no 
event  shall  the  Warranty  Commencement  Date  exceed  three  (3)  months  from  the 
shipment from AXEON’s manufacturing facility. The Customer shall provide proof of 
purchase  in  order  to  exercise  rights  granted  under  this  Warranty.  If  requested  by 
AXEON,  the  Customer  must  also  provide  proof  of  the  installation  date.  Proof  of 
installation  shall  be  returned  by  Customer  to  AXEON  within  thirty  (30)  days  after 
installation  by  virtue  of  supplying  a  Warranty  Validation  Card  supplied  with  each 
AXEON  product  fully  completed  and  signed  in  ink  by  Customer  and  the  authorized 
installer of the product. 

Warranty Service 

AXEON’S  OBLIGATION  UNDER  THIS  WARRANTY  IS  LIMITED  TO  THE  REPAIR 
OR  REPLACEMENT  (AT  AXEON’S  SOLE  DISCRETION)  OF  ANY  PRODUCT,  OR 

Содержание L1-Series






























Отзывы: