AWH DN10 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 28

AWH DN10 Скачать руководство пользователя страница 22

11/13

Inline Sight Glass

Operating Instructions

8.1 Disassembly from the System

8.2 Assembly with Glass Cylinder Replacement

See Pic. 7-1

1. Check the seals (Pic. 7-1, item 5) and the glass cylinder (Pic. 7-1, item 3) for damage.

2. Clean the installation space and check for any damage.

3. Clean the glass cylinder (Pic. 7-1, item 3) and the safety screen (Pic. 7-1, items 1, 2).

4. Place the seal (Pic. 7-1, item 5) in the fl ange (Pic. 7-1, item 7).

5. Position the glass cylinder (Pic. 7-1, item 3) in the fl ange so that the glass cylinder is not in contact

with any metal.

Note

Proceed carefully and meticulously to avoid damage.

6. Push the safety screen (Pic. 7-1, items 1, 2) over the glass cylinder (Pic. 7-1, item 3).

7. Carefully set the counter fl ange on the fl ange without damaging the seal (Pic. 7-1, item 5) and screw it

in place in a criss-cross pattern.

8. While screwing it in place, check the alignment of the glass cylinder between the fl anges and adjust it

if necessary. Tighten the hexagonal nuts in a criss-cross pattern.

9. Check for leaks under operating conditions.

25

HAZARD

There is a risk of

burning

during operation or maintenance if fl ow media have

temperatures over 60°C.

8. Assembly / Disassembly

When disassembling the inline sight glass from the system, proceed as follows:

1. Carry out the shutdown procedure as instructed in 5.4.

2. Drain the piping system.

3. Undo the hexagonal nuts on one side (Pic. 7-1, item 4).

4. Separate the fl anges (Pic. 7-1, item 7).

5. Remove the glass cylinder (Pic. 7-1, item 3) with seal

(Pic. 7-1, item 5) and the safety screen (Pic. 7-1, items 1, 2) from the fl ange.

Note

Disassembly must be carried out by experts only. Always ensure that the shut-

down procedures are followed before starting any disassembly work.

«
...
20
21
22
23
24
...
»

Содержание DN10





























Отзывы:

Нет отзывов