AWB OD200-IDU Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 114

background image

iii

About This Guide

Purpose

This guide details the hardware features of the WiMAX Residential Gateway including its
physical and performance-related characteristics, and how to install the device and use its
configuration software.

Audience

The guide is intended for use by network administrators who are responsible for operating
and maintaining network equipment; consequently, it assumes a working knowledge of
general networking concepts, the Internet Protocol (IP), and Simple Network
Management Protocol (SNMP).

Conventions

The following conventions are used throughout this guide to show information:

Note:

Emphasizes important information or calls your attention to related features or
instructions.

Caution:

Alerts you to a potential hazard that could cause loss of data, or damage the
system or equipment.

Warning:

Alerts you to a potential hazard that could cause personal injury.

Related Publications

The following publication gives basic information on how to install and use the WiMAX
Residential Gateway.

Quick Installation Guide

As part of the WiMAX Residential Gateway’s software, there is online help that describes
all configuration related features.

Revision History

This section summarizes the changes in each revision of this guide.

December 2008 Revision

This is the first revision of this guide. This guide is valid for software release v0.2.0.3.

«
...
5
6
7
8
9
...
»

Содержание OD200-IDU



















































































































Отзывы:

Нет отзывов

Похожие инструкции для OD200-IDU

Бренд: D-Link Страницы: 2

Бренд: D-Link Страницы: 59

Airspot DSA-3100

Бренд: D-Link Страницы: 70

Бренд: Bivocom Страницы: 49

Бренд: New Rock Technologies Страницы: 75

Бренд: SIEB & MEYER Страницы: 40

Бренд: Ruckus Wireless Страницы: 2

VBG-PN-K20-DMD-EV

Бренд: Pepperl+Fuchs Страницы: 11

Бренд: Zenitel Страницы: 14

Бренд: Gree Страницы: 21

myTalker ET7000

Бренд: Tekkeon Страницы: 2

Бренд: Funkwerk Страницы: 594

Gateway 2070 Series

Бренд: 2Wire Страницы: 4

Kona Mega Gateway

Бренд: TEKTELIC Communications Страницы: 16

Kona Macro Gateway

Бренд: TEKTELIC Communications Страницы: 32

Бренд: gefran Страницы: 2

MediaAccess TG789vn

Бренд: Technicolor Страницы: 128

Бренд: Lauda Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды